46
11) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes
the setting of the equipment into the dashboard easier.
See cabling diagram page 73.
12) PTT ~ RF POWER ~ MIC GAIN ~ TALKBACK
PTT (Push To Talk)
Transmission switch, press to transmit a message,
is displayed
and release to listen to an incoming communication.
RF POWER
See §
RF POWER
page 43
MIC GAIN
See §
MIC GAIN
page 45
TALKBACK
(combination 12 / 10)
The
TALKBACK
function allows to ear your own modulation with
the CB speaker.
While pressing
PTT
switch (
12
),
- Press
F
key (
10
) to
activate
/
deactivate
TALKBACK
function. When
the function is
on
,
“TALKBACK”
is displayed.
TALKBACK LEVEL
(12 / 5)
When the
TALKBACK
function is
on
, press and hold
PTT
switch (
12
)
and turn the rotary
CH
knob (
5
) to
adjust
the
TALKBACK
level. 9
steps from
01
to
09
.
TOT (Time Out Timer)
If the transmission (using the
PTT
(
12
) key or
VOX
)
is more than 5
minutes, CHANNEL and
start blinking, the transmission ends.
The time-out tone will sound until the
PTT
key is released.
13) UP/DN BUTTONS ON MICROPHONE
-
These buttons (
13
) allow
increase
(
UP
) or
decrease
(
DN
) the chan-
nel. A beep sound is emitted whenever the channel is changed if
the
KEY BEEP
function is activated
(see
BEEP KEY
function on page
47)
.
The display shows the corresponding frequency. For example
“
27.205
”
for channel
40
.
See
SPAN
menu page 48.
See §
CHANNEL SELECTOR CH
on page 43.
C) FUNCTION TURNING ON THE UNIT
To
select
the
FREQUENCY BAND
turn
off
the unit. Press and hold
the
F
key (
10
) and then turn the unit
on
.
(Configuration: EU; PL; d; EC; U; In)
The frequency bands have to be chosen according to the country
of use. Don’t use any other configuration. Some countries need a
user’s licence.
See table page 75
.
1.
Turn on the power while pressing the
F
key (
10
). The letter corre-
sponding to the current configuration is blinking.
2.
In order to change the configuration, turn the rotary
CH
knob (
5
)
on the unit or use the
UP
/
DN
buttons (
13
) on the microphone.
3.
When the configuration is selected, press the
F
key (
10
) during 1
second. The letter corresponding to the configuration is continu-
ously displayed and a confirmation beep sounds.
4.
At this point, confirm the selection by switching off the transceiver
and then switching it on again.
See the frequency bands table at pages 70 to 72 / configu-
ration table page 74.
D) MENU
The order of the 14 functions is the one described in this manual.
However, the function displayed when entering the
MENU
will be
the last function modified by the user.
Whatever the function, the procedure is the same:
Press the
CH
knob (
5
) for 3 seconds to enter
MENU
. appears.
1.
Turn the rotary
CH
knob (
5
) or use the
UP/DN
buttons (
13
) on the
microphone to
select
the menu.
2.
Press the
CH
knob (
5
) to
confirm
. The setting parameter of the
selected menu flashes in the display.
3.
Turn the rotary
CH
knob (
5
) or use the
UP/DN
buttons (
13
) on the
microphone to
change
the parameter value.
English
