43
5) CHANNEL SELECTOR CH ~ RF POWER
CHANNEL SELECTOR CH
- Turn the rotary
CH
knob (
5
) to
move
up or down a channel. A
beep sound is emitted each time the channel is changed if the
KEY BEEP
function is activated
(see
KEY BEEP
function on page
47)
.
See §
UP/DN BUTTONS ON MICROPHONE
page 46.
The display shows the corresponding frequency. For example
“
27.205
”
for channel
40
.
See
SPAN
menu page 48.
- A long press (3 seconds) on this button (
5
) allows entering the
MENU
.
- A short press on this button (
5
) validates the settings in the
MENU
.
RF POWER
(combination 12 / 9 + 5)
In
TX
mode,
increase
/
decrease
the output power.
- Press and hold the
PTT
switch (
12
).
- Press the • (
9
) and
CH
(
5
) buttons.
«
RF POWER
»
is displayed.
- Turn the rotary
CH
knob (
5
) to
adjust
the level using the bargraph.
- Press the
CH
knob (
5
) for 1 second to confirm the setting.
6) MODE ~ PA ~ •VOX ~ • VOX SETTING
MODE
(short press)
This switch allows
selecting
the modulation mode AM, FM, LSB or
USB; Your modulation mode has to correspond to the one of your
correspondent.
-
Amplitude Modulation / AM:
communication on a field with relief
and obstacles at middle distance (the most used).
-
Frequency Modulation / FM:
for nearby communications on a flat
open field.
In U configuration only:
in FM mode, a long press on the
F
key
(
10
)
alternates
between the
ENG
or
CEPT
frequency bands.
“UK”
is displayed when the
ENG
frequency band is selected
(see table
on page 70)
.
-
Upper and Lower Side Band / USB-LSB:
used for long distance
communications (according to the propagation conditions).
PA (Public Address)
(long press)
Long press
PA
key (
6
) to
alternate
between
CB
and
PA
mode.
An external loud speaker can be connected to the unit
by the PA jack plug located on the back panel PA.SP. (
D
).
For details on operating in
PA
mode, see the
PA SETTING
menu on page 50.
VOX
(9 + 6 short press)
The
VOX
function allows
transmitting
by speaking into the original
microphone (or in the optional vox microphone) without pressing
the
PTT
switch (
12
). The use of an optional vox microphone con-
nected to the rear panel of the transceiver (
E
) disables the original
microphone.
Press
•
key (
9
) and short press •
VOX
key (
6
) in order to
activate
the
VOX
function.
“VOX”
appears on the display. Repeat the key
combination to disable the function.
“VOX”
disappears.
VOX SET
(9 + 6 long press)
Press the
•
key (
9
) and press during 1 second the •
VOX
key (
6
) in
order to
activate
the function
VOX SETTING
.
“VOX”
is displayed.
Three adjustments are possible: Sensitivity
SET-L
, Anti-vox level
SET-A
and Vox delay time
SET-T
. The
Display shows the type of adjustment followed by its level , for
example
SET-L1
.
1.
Turn the
CH
knob (
5
) to
increase
/
decrease
the level of the active
setting.
2.
Press the •
VOX
key (
6
) briefly to go to the next setting.
3.
Once the
VOX
is correctly set, a long press (1 second) on the
•
VOX
key (
6
) will
save
the settings and
exit
the
VOICE SETTING
function.
-
Sensitivity
“
SET-L
”
: allows the adjustment of the microphone (original
one or optional vox) for an optimum transmission quality. Adjustable
level from
1
(high level) to
9
(low level).Default value:
1
.
-
Anti-Vox
“
SET-A
”
: allows disabling the transmission generated by
the surrounding noise. The level is adjustable.
OFF
(according the
English
