Premium PWDC191FM Service Manual Download Page 25 | Manualshive

Page: 25 / 33

background image

P.25

Operation step

Picture

　　　　　　　　　　　　　　　

4.UNPACKING WAYS OF MAIN PARTS

21 Undo the panel support

Undo the top cover

(methods as followed).

Undo the control panel.
Remove two screws

fixing the panel support,
and then remove it.

①

②
③

22 Undo the drum tub assembly

Remove the motor in

24(methods as followed).

Pull out the heater.
Remove the belt.

①

②
③

Remove the screws

fixing the pulley, and then
take out the pulley.

④

20 Undo the door glass

Open the door, remove

two screws fixing the
hinge and front plate, and
then remove the door.

Remove 12 screws on

the inner door.

Remove the outer door

and the inner door with
special tool.

Take out the door glass.

①

②

③

④

«
...
23
24
25
26
27
...
»

Summary of Contents for PWDC191FM


































Reviews:

No comments

Related manuals for PWDC191FM

Brand: bar aid Pages: 16

Spacemaker WSLP1500JWW

Brand: GE Pages: 3

Brand: Kärcher Pages: 196

Brand: Kärcher Pages: 65

Brand: Kärcher Pages: 20

Brand: Kärcher Pages: 208

HD 4.5/32-4 S Eb HD 4.5/32-4 S Ec

Brand: Kärcher Pages: 36

Brand: Kärcher Pages: 44

Brand: Kärcher Pages: 264

Brand: Zanussi Pages: 3

Brand: Zanussi Pages: 20

Brand: Zanussi Pages: 24

Brand: Zanussi Pages: 16

Brand: Indesit Pages: 24

Brand: Thermador Pages: 20

Brand: Kärcher Pages: 7

Brand: Kärcher Pages: 112

AQUALTIS AQLF8F 292 U

Brand: Hotpoint Ariston Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands