Premium PWDC191FM Service Manual Download Page 20 | Manualshive

Page: 20 / 33

background image

P.20

Operation step

Picture

　　　　　　　　　　　　　　

4.UNPACKING WAYS OF MAIN PARTS

Picture

　　　　　　　　　　　　　　

④

5

Undo five screws in

the front plate.

Put the front plate up

to the clasp of the front
plate away from the
loading holder, and then
take off the front plate.

①

②

.

③

Loosen

8 Undo the gasket

Undo the top cover,

control panel, lower cover,
machine door and the front
plate(methods as
followed).

Remove the outer

gasket clamp between the
door seal and the front
plate

the inner gasket

clamp between the door
seal and the front of the
outer tub, and take out the
gasket.

9 Undo the PCB panel
Undo the top cover
and control panel(methods
as followed).

7Undo the facade counterweight

Undo the front plate

(methods as followed).

Remove six screws pull out

①

②

the facade counterweight.

«
...
18
19
20
21
22
...
»

Summary of Contents for PWDC191FM


































Reviews:

No comments

Related manuals for PWDC191FM

Brand: Heinner Pages: 93

WD0894W8 Series

Brand: Samsung Pages: 88

Brand: Philco Pages: 192

Brand: Ryobi Pages: 12

Powerplus GardenPro POWXG9009

Brand: VARO Pages: 13

Brand: maxwatt Pages: 38

Brand: Kärcher Pages: 20

Profile PDT750SMFES

Brand: GE Pages: 48

Brand: PowerStroke Pages: 44

Challeng Air AIRMAX

Brand: Double K Industries Pages: 4

Monogram ZBD0710

Brand: GE Pages: 48

Brand: Samsung Pages: 60

Brand: Samsung Pages: 68

Brand: Samsung Pages: 68

WD752U4BK Series

Brand: Samsung Pages: 88

WD702U4BK Series

Brand: Samsung Pages: 88

Brand: Samsung Pages: 118

Brand: Samsung Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands