background image

PDS-PLUS/PDS-PLUS-W

Page 16 

Visit the Premier Mounts website at http://www.mounts.com

 

Installation Instructions

PREMIER MOUNTS

LIMITED LIFETIME WARRANTY

What and Who is Covered by this Limited Warranty and for How Long

Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original 

owner of this product.  The limited warranty is valid only for the original purchaser of the product.

What Premier Mounts Will Do

At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.  

If Premier Mounts chooses to replace a defective product or part, a replacement product or part will be shipped to you 

at no charge, but you must pay any labor costs. 

What is Not Covered; Limitations

PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS, 

PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM 

IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS. 

PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES 

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  PREMIER MOUNTS IS NOT 

RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO, 

INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE 

PRODUCTS OR PARTS.  SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR 

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.  

What Customers Must Do for Limited Warranty Service

If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address 

below within thirty (30) days.  Proof of purchase (an original sales receipt) from the original consumer purchaser must 

accompany all warranty claims.  Warranty claims must also include a description of the problem, the purchaser’s name, 

address, and telephone number.  General inquiries can be addressed to Premier Mounts Customer Service at 1-800-

368-9700.  Warranty claims will not be accepted over the phone or by fax.

 

Premier Mounts

 

Attn: Warranty Claim

  

1321 S. State College Blvd.

 

Fullerton, CA 92831

How State Law Applies

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH 

VARY FROM STATE TO STATE.

©Premier Mounts 2009

Warranty

Disclaimer

Premier Mounts intends to make this manual accurate and complete. However, Premier Mounts makes no claim that 

the information contained herein covers all details, conditions or variations, nor does it provide for every possible 

contingency in connection with the installation or use of this product. The information contained in this document 

is subject to change without notice or obligation of any kind. Premier Mounts makes no representation of warranty, 

expressed or implied, regarding the information contained herein. Premier Mounts assumes no responsibility for 

accuracy, completeness or sufficiency of the information contained in this document.

Warranty

Summary of Contents for PDS-PLUS

















Reviews: