Premier Mounts ECM-D70T Installation Manual Download Page 2

Phillips Screw 

Driver

Protective Eye Wear

Tape Measure

Pencil

Ladder

ECM-D70T / ECM-D70T1.5

Installation Guide

www.mounts.com  |  North America  800.368.9700  | Interna1-714-632-7100

Required for installation

PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS MUST BE READ AND  

COMPLETELY UNDERSTOOD TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLA-

TION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.

INSTALL THE MOUNT ACCORDING TO THE INSTRUCTIONS PROVIDED BY PREMIER MOUNTS. PERFORM ALL STRUC-

TURAL REINFORCEMENTS BEFORE ATTACHING THE FLAT PANEL TO THE CEILING MOUNT. USE THE APPROPRIATE 

LIFTING DEVICE WHEN LIFTING THE FLAT PANEL INTO PLACE. 

PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS  

PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAU-

THORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, 

SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MAN-

NER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.

SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER 

SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.

At least two qualified people should perform the assembly procedure. Personal injury and/or property damage can result from 

dropping or mishandling the flat-panel.

Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no 

electrical wires in the ceiling. Cutting or drilling into an electrical line may cause serious personal injury.

Make sure there are no water or natural gas lines inside the ceiling where the mount is to be located. Cutting or drilling into a 

water or gas line may cause severe property damage or personal injury.

This product is intended for indoor use only. Use of this product outdoors could lead to product failure and/or serious personal 

injury.

Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact.

 Weight Capacity

 Warning Statements

Maximum flat-panel weight:

180lbs.

THE CEILING STRUCTURE MUST BE CAPABLE OF HOLDING FOUR (4) 

TIMES THE WEIGHT OF THE FLAT PANEL AND MOUNT. IF NOT, THEN 

THE CEILING STRUCTURE MUST BE REINFORCED.

Contact Premier Mounts with any questions: 

(800) 368-9700

Page 2

Summary of Contents for ECM-D70T











Reviews: