manualshive.com logo in svg

Precor C844, User Manual, Page: 13 / 54

Share
Download
Precor C844 User Manual Download Page 13

C844 Upright Cycle

Page 13

Section Four - Checking Unit Operation

This section provides you with a quick method of checking cycle operation. Check the operation 
of the C844 Cycle at the end of most maintenance procedures.

Procedure

1.

Plug the power cord into the wall outlet, then turn on the bike with the circuit breaker.

2.

If the display does not illuminate refer to procedures 6.3 0r 6.4.

3.

When the 

PRESS ENTER FOR PROGRAMS

 prompt appears, press 

QUICK START

. 

4.

Select Work Level 1 and press 

ENTER

.

5.

Operate the C844 for 4–5 minutes. As you operate the cycle, concentrate on the resistance 
and operating sounds of the unit. Be on the alert for unusual rubbing, hitting, grinding or 
squeaking noises.

6.

Press the 

WORK LEVEL UP

 

key until you reach Work Level 5. Operate the cycle for 

another 2–3 minutes.

7.

If the resistance of the cycle does not change or the operation of the cycle feels inconsistent 
compared with Work Level 1 . . .

THEN . . .

OTHERWISE . . .

Refer to procedures 6.5 and 6.6

Continue with the next step.

8.

Press the 

WORK LEVEL UP

 

key until you reach Work Level 10. Operate the cycle for 

another 2–3 minutes.

9.

If the resistance of the cycle does not change or the operation of the cycle feels inconsistent 
with Work Levels 1 and 5 . . .

THEN . . .

OTHERWISE . . .

Refer procedures 605 and 6.6

Continue with the next step.

10. Check the LED’s mounted on the upper PCA and the function keys displayed on the elec-

tronic console by performing Procedure 2.1.

11. If the keys do not respond appropriately, refer to procedure 6.2.

Summary of Contents for C844























































Reviews:

No comments