background image

EXPERIENCE™ SERIES AMT

GETTING STARTED GUIDE 

Welcome to a 

personalized fitness experience

 for your members 

The Experience™ Series cardio line gives operators the proven, reliable performance they count on. Each piece delivers the personalized 

exercise experience and entertainment choices your members seek. The Adaptive Motion Trainer (AMT) keeps exercisers engaged, 

challenged, and loyal. For more information about the AMT, visit us at 

www.amtfitness.com

Get to know Precor equipment 

The AMT with Open Stride™ lets the exerciser adjust stride 

height from 6.8 to 10 inches (17 to 25 cm). Combine this with 

the AMT’s ability to dynamically adapt the exerciser's stride 

length from 0 to 36 inches (0 to 91 cm). Open Stride applies to 

AMT 800 models only. AMT with dynamic stride length applies 

to AMT 800 and AMT 700 models. 

The 

StrideGuide™ 

diagram illustrates the ratio of stride length to 

stride height. 
AMT offers a total body workout in one piece of equipment: 

Handlebar positions are optimized for pushing and pulling

motions

Helps exercisers burn more calories with more enjoyment

Monitor stride length with Stride Dial™

The AMT fully engages exercisers of all fitness levels with an infinite range of stride paths to create a uniquely effective 

low-impact workout, making every workout a personalized experience. Your members get boundless training variety without 

the need to change machines: improve aerobic and anarobic fitness, as well as strength, coordination, and balance on the 

AMT. 

Get to know Precor cardio workouts 

Our instructional videos provide information vital to the safe and effective use of the equipment and can help users, 

trainers, and operators get the most out of their EFX. 
A variety of manual and preset programs such as Lose Weight, Be Fit, Get Toned, and Push Performance can help 

trainers and users meet their goals and build training programs tailored to produce the best possible results. 

Instructional videos and complete EFX operating instructions are available at 

www.precor.com

Also available at 

precor.com

 are regularly-updated blog posts with more ideas about fitness routines 

and advice from trusted industry experts

.

 

AMT Getting Started Guide  |  P/N 304439-101 rev 

C

, ENU 

©

2017 

Precor Incorporated  |  

June

 201

7

 

Summary of Contents for AMT 885














































Reviews: