P
RO
V
U
™ PD6000 Analog Input Process Meter
Instruction Manual
13
Transmitter Supply Voltage
Selection (P+, P-)
All meters, including models equipped with the
12-24 VDC power option, are shipped from the
factory configured to provide 24 VDC power for
the transmitter or sensor.
If the transmitter requires 5 or 10 VDC excitation,
the internal jumper J4 must be configured
accordingly.
To access the voltage selection jumper:
1. Remove all the wiring connectors.
2. Unscrew the back cover.
3. Slide out the back cover by about 1
inch.
4. Configure the J4 jumper, located behind
the input signal connector, for the
desired excitation voltage as shown.
Figure 5. Transmitter Supply Voltage Selection
Connections
All connections are made to removable screw
terminal connectors located at the rear of the
meter.
•
Use copper wire with 60°C or 60/75°C insulation
for all line voltage connections. Observe all safety
regulations. Electrical wiring should be performed
in accordance with all applicable national, state,
and local codes to prevent damage to the meter
and ensure personnel safety.
Connectors Labeling
The connecto
rs’ label, affixed to the meter, shows the
location of all connectors available with requested
configuration.
Note: ## on the following figures refers to power and
display options. (Example: PD6000-6H5)
Figure 6. PD6000-##0 Connectors Label
Figure 7. PD6000-##2 Connectors Label
Figure 8. PD6000-##3 Connectors Label
Figure 9. PD6000-##4 Connectors Label
Figure 10. PD6000-##5 Connectors Label
Figure 11. PD6000-##7 Connectors Label
•
DO NOT
connect any equipment other than
Precision Digital’s expansion modules, cables, or
meters to the RJ45 M LINK connector. Otherwise
damage will occur to the equipment and the
meter.
POWER
+
-
SIGNAL
M-LINK
1 2 3 4 5 6 7 8
2
1
P-
COM
P+
V+
mA+
3
4
1
2
5
F4
6
POWER
+
-
SIGNAL
M-LINK
C
NO
NO
NC
NC
C
RELAY2
RELAY1
4
3
6
5
2
1
1 2 3 4 5 6 7 8
2
1
P-
COM
P+
V+
mA+
3
4
1
2
5
F4
6
R
I-
I+
MA OUT
1
3
2
POWER
+
-
SIGNAL
M-LINK
1 2 3 4 5 6 7 8
2
1
24 V
P-
COM
P+
V+
mA+
3
4
1
2
5
F4
6
POWER
+
-
SIGNAL
M-LINK
C
NO
NO
NC
NC
C
RELAY4
RELAY3
4
3
6
5
2
1
C
NO
NO
NC
NC
C
RELAY2
RELAY1
4
3
6
5
2
1
1 2 3 4 5 6 7 8
2
1
P-
COM
P+
V+
mA+
3
4
1
2
5
F4
6
R
I-
I+
MA OUT
1
3
2
POWER
+
-
SIGNAL
M-LINK
C
NO
NO
NC
NC
C
RELAY2
RELAY1
4
3
6
5
2
1
1 2 3 4 5 6 7 8
2
1
24 V
P-
COM
P+
V+
mA+
3
4
1
2
5
F4
6
R
I-
I+
MA OUT
1
3
2
POWER
+
-
SIGNAL
M-LINK
C
NO
NO
NC
NC
C
RELAY4
RELAY3
4
3
6
5
2
1
C
NO
NO
NC
NC
C
RELAY2
RELAY1
4
3
6
5
2
1
1 2 3 4 5 6 7 8
2
1
24 V
P-
COM
P+
V+
mA+
3
4
1
2
5
F4
6
