PPI UniRec User Manual Download Page 25

Page: 25 / 27

ELECTRICAL CONNECTION

The Electrical Connection Diagram is shown on the Top Side of the enclosure. The diagram shows the terminals viewed from

the REAR SIDE with the front label upright. The terminal numbers are also embossed on the rear side of the enclosure. Refer

figure 12.1.

Figure 12.1

DIGITAL INPUT FOR BATCH START COMMAND

Connect a remote potential-free contact closure switch for the purpose of issuing the Batch -

Recording START command. An ‘OPEN’ to ‘CLOSE’ change over of the contacts initiates time

based batch recording. Once the recording starts, the change in the contact status has no effect.

Figure 12.2

Batch Start

Switch

DIGITAL INPUT FOR ALARM ACKNOWLEDGE

Connect a remote potential-free contact closure switch for the purpose of issuing Alarm

Acknowledgment. An ‘OPEN’ to ‘CLOSE’ change over of the contacts acknowledges the alarm and

mutes the alarm relay(s).

Figure 12.3

Switch

Alarm ACK

ALARM-1 RELAY OUTPUT

This relay output status is determined by logically ORing the Alarm-1 status of all the devices.

Potential-free Relay changeover contacts NO (Normally Open) and C (Common) rated 2A/240

VAC (resistive load) are provided as Relay output.

Figure 12.4

Alarm-1

15 16

RLY

User Manual

UniRec

Section 12

Summary of Contents for UniRec




























Search results

Summary of Contents for UniRec

Reviews:

Related manuals for UniRec

Brands by name

Popular brands

PPI UniRec, User Manual

Search results

Summary of Contents for UniRec

Reviews:

Related manuals for UniRec

Brands by name

Popular brands