Powersolve RED00202A, Manual

Page: 5 / 6

RED00202(R2) MANUAL
Connections
Clamping Yoke Connector Specifications
Input / Output connections Signal connection plug
Tightening torque min. – max. 1,2 – 2,2Nm (blade 1,0x5,5 DIN5264 ) 0,4 – 0,5Nm (blade 0,6x3,5 PH1 PZ1)
Touch-safe protection acc. to DIN VDE 0470 IP20 plugged/ IP10 unplugged Not applicable
Clamping range, min. – max. 0,5 – 16mm² / AWG26 – AWG6 0,2 – 4,0mm² / AWG26 – AWG12
Solid, H05(07) V-U min. – max. 0,5 – 16mm² 0,2 – 4,0mm²
Stranded, H05(07) V-U min. – max. 6 – 16mm² Not applicable
Flexible, H05(07) V-U min. – max. 0,5 – 16mm² 0,2 – 4,0mm²
w. plastic collar ferrule, DIN 46228 pt 4 min. – max. 2,5 – 10mm² 0,2 – 2,5mm²
w. wire end ferrule, DIN 46228 pt 1, min. – max. 2,5 – 10mm² 0,2 – 4,0mm²
Plug gauge in accordance with EN 60999 a x b; ø
5,4 x 5,1mm; 5,3mm 2,8 x 2,4mm; 2,5mm
Pitch (P) 10,16mm 7,50mm
Wire Stripping Length (fine wired)
Nominal Cross Section Wire End Ferrule Stripping Length Wire End Ferrule Stripping Length
0,25mm² H0,25/5 5mm H0,25/10 HBL 8mm
0,5mm² H0,5/6 6mm H0,5/12 OR 8mm
1,0mm² H1,0/6 6mm H1,0/12 GE 8mm
2,5mm² H2,5/12 12mm H2,5/19D BL 14mm
4,0mm² H4,0/12 12mm H4,0/20 GDR 14mm
6,0mm² H6,0/20 12mm H6,0/20 SW 14mm
10,0mm² H10,0/12 12mm H10,0/22 EB 15mm
The length of ferrules is to be chosen depending on the rated voltage. The outside diameter of the plastic collar should not be larger than
the pitch (P)
Ordering Information
Ordering Codes
Product Code Volt Power Information Article Number
RED00202A(R2) 0 – 28Vdc 1000W below 12Vdc is the DC-OK relay without function 3041049001CA
RED00202B(R2) 36 – 60Vdc 1000W 3041049002CA
RED00202C(R2) 90 – 125Vdc 1000W 3041049003CA
Electrical Safety (Factory-Test / Field-Test Owner)
Type and factory test are the manufacturer. While repeating damage can
happen to the power supply unit. For the field test (owner) follow the below instruction:
a) Use suitable test equipment, raising the voltage slowly.
b) Use only test voltages of 50/60Hz. The outputs are unearthed and
therefore they have no resistance to GND/PE.
c) If the residual voltage is
≥
60Vdc, observe the safety standards.
Use only specially insulated screwdriver to trim the Ua/Ia.
T A
1)
B
Type Test 60s 500Vac 500Vdc
Factory Test 5s 500Vac 500Vdc
Field Test 2s 500Vac 500Vdc
Cut-off current setting >1mA >1mA
1)
≥ 60Vdc = 1500Vdc
sales@powersolve.co.uk www.powersolve.co.uk 020321