PowerPlus Energy ECo 4840P Installation And Operation Manual Download Page 34 | Manualshive

Page: 34 / 37

PowerPlus Energy ECo 4840P Installation And Operation Manual Download Page 34

7.1.3. BMS Threshold Hard Shutdown

Hard shutdown occurs if the voltage in the battery is too LOW to activate the internal BMS. This is a
hardware triggered response.

7.1.4. Hard Shutdown Recovery

Required Equipment:

1. External DC Charger/Current Limited Power Supply (Available from PowerPlus Energy).

50V Charger/Current Limited Power Supply for Eco4840P

2. Cold Start dongle

Eco4840P:
1. Turn off Battery/s via on board DC breaker.
2. Connect DC Charger/Current Limited Power Supply to battery/s.
3. Check DC Charger is set to battery Nominal Voltage specified in the this manual (See Specification).
4. Turn on battery/s via DC breaker.
5. Turn on external charger.
6. Wait for Main Status LED to turn on.
7. Reconnect on site PCE to the recovered battery and action a full charging cycle enabling the battery to

balance at Continuous Charge Voltage (See Specification) for at least 4 hours.

Important:

It is recommended to check the battery status once a month for 3 months after battery recovery has
occurred to ensure reliable operation of the battery module.

Eco P Series Installation Manual V3.0

21/10/2021

Page

of

34

37

«
...
32
33
34
35
36
...
»

Summary of Contents for ECo 4840P






































Reviews:

No comments