Powerbuilt EGS0252 Instruction Manual Download Page 36

Page: 36 / 40

SPECIFICATIONS

Hose

• Do not allow hoses to come in contact with

engine muffler during or immediately after use.

• DO NOT pull unit by pressure hose.

Engine

• Do not adjust or attempt maintenance without

consulting supplied engine manual or having

adjustments made at an authorized service center.

• Add stabilizer to petrol tank and let engine run for

5 minutes before storage.

• Always turn on water before starting engine.

Soap/Chemicals

• Use only soaps and chemical detergents designed

for waterblaster use.

• Use Chemical nozzle (Black) with Soap/Chemicals.

Nozzle

• Always keep nozzles unclogged.

• Chemical/soap solutions cannot be applied using

high pressure setting. Set pressure pump to low

pressure and use low pressure nozzle.

Storage or Winterizing

• Run clean water through chemical inlet.

• Add stabilizer to any remaining petrol in petrol tank.

• Do not allow water to freeze in pressure pump,

spray gun, spray wand or hoses.

Max Pressure

2400PSI

Max Water Flow

12LPM

Pump Type

Triplex

Engine/Type

Powerbuilt XT210 /OHV

HP/RPM

7 / 3600

Displacement

207CC

Petrol/Detergent Tank Capacity

3.6 / 3.8Liter

Pressure Hose

10Meter

Low Oil Sensor

YES

Thermal Relief Valve

YES

Adjustable Pressure Regulator

YES

Summary of Contents for EGS0252








































Search results

Summary of Contents for EGS0252

Reviews:

Related manuals for EGS0252

Brands by name

Popular brands

Powerbuilt EGS0252, Instruction Manual

Search results

Summary of Contents for EGS0252

Reviews:

Related manuals for EGS0252

Brands by name

Popular brands