background image

3

Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com

Specifications

Description

Submersible non-clog sewage pumps are designed for typical raw 

sewage application.

Series:  PFSE51, PFSE51A,

PFSE51HT, PFSE52, PFSE594, 

PFSE544, PFSE554

0.5 HP • 1750 RPM • 60 Hz

Standard & High Temperature

DISCHARGE

2” NPT, Female, Vertical

LIQUID 

TEMPERATURE

Standard - 104°F Continuous

High Temp - 200°F Continuous

VOLUTE

Cast Iron, Class 30

MOTOR HOUSING

Cast Iron, Class 30

IMPELLER

2 Vane, Open Type

Material: Cast Iron, Class 30

SHAFT

Stainless Steel

SEAL PLATE

Cast Iron, Class 30

O-RINGS

Buna-N (on Std) Silicon (on High Temp)

HARDWARE

Stainless Steel

PAINT

Powder Coated - Industrial Grade

SEAL

Inboard, Single Mechanical, Oil Filled,

Material: Carbon/Ceramic/Buna-N

POWER CORD

15 Ft. Cord, with Plug on 115 Volt & 1/2HP, 

230 Volt 1 Phase. Fast Disconnect Design.

MOTOR

Oil Filled, Squirrel Cage Induction

Class B Insulation

SINGLE PHASE

Permanent Split Capacitor (PSC),

Includes Overload Protection in Motor:

STD Trip Off Temp. 248°F (120° C),

HT Trip Off Temp. 293°F (145° C)

THREE PHASE

200-230/460 is Tri-Voltage motor. Requires 

overload protection to be included in control 

panel

UPPER BEARING

Single Row, Ball, Oil Lubricated

LOWER BEARING

Single Row, Ball, Oil Lubricated

LEVEL CONTROL

“A”

Wide Angle, Mechanical Float, 15Ft. Cord

with Piggy-Back Plug, Normally Open (N/O).

3.50” tether, Adjustable

Optional 3” Discharge Flange available

Series:  PFSE774, PFSE794,

 

 

PFSE744, PFSE754

0.75 HP • 1750 RPM • 60 Hz

Series:  PFSE1074, PFSE1094,

PFSE1044, PFSE1054

1.0 HP • 1750 RPM • 60 Hz

PFSE .05, .75 & 1HP 

 

 

 

 

 

 

 

 

Sewage Pumps

PFSE51HT - High Temp

PFSE - Standard Temp

Summary of Contents for PFSE1044 Series

















Reviews: