background image

16

Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com

PFSE .05, .75 & 1HP 

 

 

 

 

 

 

 

 

Sewage Pumps

2 YEAR WARRANTY

Manufacturer warrants, to the purchaser and subsequent owner during the warranty period, new pump product 
to be free from defects in material and workmanship under normal use and service, when properly used and 
maintained, for a period of 2 years from date of sale. The date of sale shall be determined by a dated sales receipt 
noting the model and serial number of the pump. The dated sales receipt must accompany the returned pump 
if the date of the return is more than 2 years from the date of manufacturer. Product will be repaired, replaced 
or remanufactured at Manufacturer’s option. No allowance will be made for shipping charges, damages, labor 
or other charges that may occur due to product failure, repair or replacement. This warranty does not apply to 
and there shall be no warranty for any material or product that has been disassembled without prior approval 
of Manufacturer, subjected to misuse, misapplication, neglect, alteration, accident or act of God; that has not 
been  installed,  operated  or  maintained  in  accordance  with  Manufacturer’s  installation  instructions;  that  has 
been exposed to outside substances including but not limited to the following: sand, gravel, cement, mud, tar, 
hydrocarbons,  hydrocarbon  derivatives  (oil,  gasoline,  solvents,  etc.),  or  other  abrasive  or  corrosive  substances, 
wash towels or feminine sanitary products, etc. in all pumping applications. The warranty set out in the paragraph 
above is in lieu of all other warranties expressed or implied; and we do not authorize any representative or other 
person to assume for us any other liability in connection with our products.

Contact  Manufacturer  at:  1-877-24PUMPS  or  www.powerflopumps.com,  Attention:  Customer  Service 
Department, to obtain any needed repair or replacement of part(s) or additional information pertaining 
to  our  warranty.  MANUFACTURER  EXPRESSLY  DISCLAIMS  LIABILITY  FOR  SPECIAL,  CONSEQUENTIAL  OR 
INCIDENTAL DAMAGES OR BREACH OF EXPRESSED OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY 
OF FITNESS FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION 
OF THE EXPRESSED WARRANTY.

Some states do not allow limitations on the duration of an implied warranty, so the above limitation may not apply 
to you. Some states do not allow the exclusion or limitation of incidental or con sequential damages, so the above 
limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have 
other rights which vary from state to state.

Summary of Contents for PFSE1044 Series

















Reviews: