MOUNTING THE ADAPTER FOR DUST
EXTRACTION
Fig. E & F
Use the dust adapter for the extraction of dust.
•
Mount the dust adapter (15, Fig. E) with the screws (21) on
the cutter sole (3).
•
Place the dust tube (62) in the dust output (16 Fig. F).
•
Place the tube of your vacuum cleaner on the dust tube (62,
Fig. F).
Keep the outlet of the machine behind the machine for a
good view on the workpiece.
OPERATION
Always observe the safety instructions and applicable
regulations.
Hold the machine in rest position on the workpiece when
switching the machine on or off. The cutter in the collet may
damage the workpiece.
•
Clamp the workpiece and make sure that the workpiece
cannot slide from under the machine during the cutting
activities.
•
Hold the machine firmly and move it evenly over the
workpiece. Do not force the machine.
•
Only use cutters which do not show any signs of wear. Worn
cutters have a negative effect on the efficiency of the machine.
•
Always switch off the machine first before removing the plug
from the wall socket.
ADJUSTING THE CUTTING DEPTH
Fig. G
The cutting depth can be adjusted in three ways.
Adjustment using the height adjusting button
•
Use the height adjusting button (14, Fig.A) to set a fixed cutting
depth. Rotate the button clockwise to lower the machine’s
height; rotate the button counterclockwise to raise the
machine’s height.
Adjustment using the scale
•
Loosen the locking bolt of the depth stop (9).
•
Release clamping lever (11) and press the machine so far
down until the cutter touches the workpiece.
•
Tighten the clamping lever again.
•
Lower the depth stop (10) completely by rotating the button
counterclockwise.
•
Tighten the locking bolt.
•
Rotate the scale (12) to 0 position (arrow indicating 0).
•
Loosen the locking bolt.
•
Set the required cutting depth using the scale (12) and the
depth stop (10)
•
Tighten the locking bolt.
•
Release clamping lever.
Adjustment using the revolver- depth stop
The revolver-depth stop enables you to quickly choose between
six different cutting depths. These are also determined by the
adjustment of the depth stop (10).
•
Adjust the required cutting depth by rotating the revolver-
depth stop (8).
SWITCHING ON AND OFF
Fig. A
•
To switch the machine on, you press down the on/off switch
(1) using your thumb. You can adjust the cutting speed by
turning the adjusting wheel (13).
•
To switch the machine off, you release the on/off switch.
Always select a low speed for cutting plastic workpieces.
Do not put the machine down when the motor is still running.
Do not place the machine on a dusty surface. Dust particles
may enter the mechanism.
MAINTENANCE
Make sure that the machine is not live when carrying out
maintenance work on the motor.
These machines have been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper machine care and
regular cleaning.
Cleaning
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free from
dust and dirt.
If the dirt does not come off use a soft cloth moistened with
soapy water. Never use solvents such as petrol, alcohol,
ammonia water, etc. These solvents may damage the plastic
parts.
Lubrication
The machine requires no additional lubrication.
Faults
Should a fault occur, e.g. after wear of a part, please contact
your local dealer.
In the back of this manual you find an exploded view showing
the parts that can be ordered.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of the
packaging materials can be recycled. Take these materials to
the appropriate recycling locations.
Take your unwanted machines to your local dealer. Here they
will be disposed of in an environmentally safe way.
GUARANTEE
The guarantee conditions can be found on the separately
enclosed guarantee card.
Wear of the cutter is not covered by the guarantee.
Ferm
5
12
Powercraft
