3. Fixer le contre-écrou (B).
B
A
R
Remplacement des goupilles de
cisaillement
La goupille de cisaillement protège le produit contre les
dommages. Elle se casse si un objet étranger pénètre
dans les pièces mobiles.
1. Si la goupille de cisaillement se casse, arrêter le
moteur.
2. Fixer une nouvelle goupille de cisaillement (A) et un
nouveau ressort de collier (B).
A
B
Pour examiner les pneus
• Maintenir les pneus exempts de carburant et d’huile
pour éviter d’endommager le caoutchouc.
• Maintenir les pneus à l’écart de souches, de pierres,
d’ornières, d’objets pointus et de tout autre objet
pouvant les endommager.
• Maintenir la pression correcte des pneus, voir
Données techniques à la page 59
.
Dégager un déflecteur de goulotte
bouché
Si le déflecteur de goulotte est bouché, ne pas
déboucher avant que les opérations suivantes soient
effectuées.
1. Relâcher simultanément l’engagement de la tarière
et celui de l’entraînement.
2. Attendre 10 secondes pour s’assurer que les tarières
sont arrêtées.
3. Utiliser l’outil de nettoyage fourni pour dégager
l’obstruction.
AVERTISSEMENT : Ne pas placer les
mains dans le déflecteur de goulotte ou
à l’intérieur du carter de tarière.
Pour nettoyer l’outil
• Nettoyer les pièces en plastique à l’aide d’un chiffon
propre et sec.
• Ne pas utiliser de nettoyeur à haute pression pour
nettoyer la tondeuse.
• Ne pas verser de l’eau directement sur le moteur.
• Utiliser une brosse pour enlever les feuilles, l’herbe
et la saleté.
621 - 005 - 31.05.2018
55
M
Muffler
The muffler keeps the noise levels to a minimum and
sends the exhaust fumes away from the operator.
Do not use the product if the muffler is missing or
defective. A defective muffler increases the noise level
and the risk of fire.
Examine the muffler regularly to make sure that it is
attached correctly and not damaged.
CAUTION: The muffler becomes very hot
during and after use and when the engine
operates at idle speed. Be careful near
flammable materials and/or fumes to prevent
fire.
Fuel safety
WARNING: Read the warning instructions
that follow before you use the product.
• Do not start the product if there is fuel or engine oil
on the product. Remove the unwanted fuel/oil and let
the product dry.
• If you spill fuel on your clothing, change clothing
immediately.
• Do not get fuel on your body, it can cause injury. If
you get fuel on your body, use soap and water to
remove the fuel.
• Do not start the product if the engine has a leak.
Examine the engine for leaks regularly.
• Be careful with fuel. Fuel is flammable and the fumes
are explosive and can cause injuries or death.
• Do not breathe in the fuel fumes, it can cause injury.
Make sure that there is a sufficient airflow.
• Do not smoke near the fuel or the engine.
• Do not put warm objects near the fuel or the engine.
• Do not add the fuel when the engine is on.
• Make sure that the engine is cool before you refuel.
• Before you refuel, open the fuel tank cap slowly and
release the pressure carefully.
• Do not add fuel to the engine in an indoor area. Not
sufficient airflow can cause injury or death because
of asphyxiation or carbon monoxide.
• Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
• Move the product a minimum of 3 m (10 ft) from the
position where you filled the tank before a start.
• Do not put too much fuel in the fuel tank.
Chemical warning
WARNING: The engine exhaust from this
product contains chemicals known to the
State of California to cause cancer, birth
defects and other reproductive harm. For
more information go to
www.P65Warnings.ca.gov.
Safety instructions for maintenance
WARNING: Read the warning instructions
that follow before you use the product.
• The exhaust fumes from the engine contain carbon
monoxide, an odorless, poisonous and very
dangerous gas. Do not start the engine indoors or in
closed spaces.
• Before you do the maintenance on the product, stop
the engine and remove the ignition cable from the
spark plug.
• Use protective gloves when you do maintenance on
the blades. The blades are very sharp and cuts can
easily occur.
• Accessories and changes to the product that are not
approved by the manufacturer, can cause serious
injury or death. Do not change the product. Always
use accessories that are approved by the
manufacturer.
• If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases.
• Only do the maintenance as given in this operator's
manual. All other servicing must be done by an
approved service agent.
• Let an approved service agent do servicing on the
product regularly.
• Replace damaged, worn or broken parts.
Assembly
To install the handles
1. Remove the 4 M8x25 flange bolts (A) from the case.
2. Use the 4 M8x25 flange bolts (A), the 4 spring
spacers (B) and the 4 flat spacers (C).
6
621 - 005 - 31.05.2018
