Potterton Titanium 24 Page 7 Installation & Service Instructions Manual Download | Manualshive

Page: 7 / 64

background image

7

1.0 Introduction

© Baxi Heating UK Ltd 2014

1.1

Description

1. The Potterton Titanium is a fully automatic gas fired wall
mounted condensing combination boiler. It is room sealed and
fan assisted, and will serve central heating and mains fed
domestic hot water.

2. The boiler is set to give a maximum output of :-

24 models -

24 kW DHW
21 kW CH (Condensing)

28 models -

28 kW DHW
25.9 kW CH (Condensing)

33 models -

33 kW DHW
30.3 kW CH (Condensing)

40 models -

40 kW DHW
34.4 kW CH (Condensing)

3. It is designed for use on Natural Gas (G20).

4. The boiler is suitable for use only on fully pumped sealed
heating systems. Priority is given to domestic hot water.

5. The boiler data badge gives details of the model, serial
number and Gas Council number and is situated on the inner
door panel or the control box. It is visible when the case front
panel is removed (Fig. 1).

6. The boiler model name and serial number are also shown on
the information label on the back of the facia door. This is for
user reference.

7. The boiler is intended to be installed in residential / domestic
environments on a governed meter supply only.

8. The boiler must be installed with one of the purpose
designed flues such as the standard horizontal flue kit, part no.
5118489 .

9.

All systems must be thoroughly flushed and treated with

inhibitor (see section 6.2).

Important:

If the boiler is installed at a high point in the

system it is strongly recommended that Automatic Air Vent

Kit 720004701 is fitted.

1.2

Contents of Pack

1. Boiler Unit (with integral timer)
2. Wall Plate (inc. taps)
3. Set of Pipes (inc. nuts)
4. Template & Quick Fit Guide
5. Literature Pack
6. Filling Loop

Fig. 1

Control Box

Case Front Panel

Data Badge

Information Label

Facia Door

«
...
5
6
7
8
9
...
»

Summary of Contents for Titanium 24

































































Reviews:

No comments

Related manuals for Titanium 24

Brand: Teba therm Pages: 12

Brand: Adveco Pages: 108

Brand: Biasi Pages: 10

Brand: REMEHA Pages: 60

Brand: ECOFOREST Pages: 140

Brand: Dunkirk Pages: 40

Brand: Biasi Pages: 8

Luna 3 Silver Space

Brand: Baxi Pages: 41

DynaFlame Series

Brand: Camus Hydronics Pages: 92

Brand: Navien Pages: 29

Brand: NTI Pages: 72

Brand: Crestron Pages: 60

Brand: Crest Audio Pages: 24

Brand: HTP Pages: 74

Brava One 25 BF

Brand: Sime Pages: 136

Continuum CONHV 250 I

Brand: Rinnai Pages: 9

Brand: Ideal Boilers Pages: 8

Brand: Potterton Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands