Potterton Titanium 24 Page 45 Installation & Service Instructions Manual Download

Page: 45 / 64

14.0 Changing Components

Fig. 81

Cover

Burner

Gasket

Extension Piece

(On 28 models only)

Collector

Venturi

Heat

Exchanger

Rear

Insulation

Cover

Insulation

Seal

Collector

Spark

Electrode

Sensing

Electrode

Leads

Venturi

Fig. 82

14.6

Burner (Fig. 81)

1. Undo the screws securing the collector to the cover and

venturi (On 28 models there is an extension piece fitted to

the cover, remove this also.

2. Withdraw the burner from the cover and replace with

the new one.

3. Examine the gasket, replacing if necessary.

4. Reassemble in reverse order.

14.7

Insulation (Fig. 82)

1. Remove the electrode leads, noting their positions. Also

remove the electrodes as described in section 14.2.

2. Undo the screws securing the collector to the venturi and

the nuts holding the cover to the heat exchanger. Draw the

collector and cover assembly away.

3. Remove the cover insulation piece.

4. Fit the new insulation carefully over the burner and align

it with the slots for the electrodes.

5. If the rear insulation requires replacement remove it and

all debris from the heat exchanger. Also it may be necessary

to separately remove the spring clip from the pin in the

centre of the heat exchanger and the ‘L’ shaped clips

embedded in the insulation.

6. DO NOT remove the shrink-wrapped coating from the

replacement rear insulation. Keep the insulation vertical and

press firmly into position.

7. Examine the cover seal and replace if necessary.

Summary of Contents for Titanium 24

































































Search results

Summary of Contents for Titanium 24

Reviews:

Related manuals for Titanium 24

Brands by name

Popular brands

Potterton Titanium 24, Installation & Service Instructions Manual

Search results

Summary of Contents for Titanium 24

Reviews:

Related manuals for Titanium 24

Brands by name

Popular brands