Potterton Titanium 24 Page 37 Installation & Service Instructions Manual Download | Manualshive

Page: 37 / 64

background image

37

11.0 Commissioning

© Baxi Heating UK Ltd 2014

Set Boiler to Maximum Rate

(see 11.1.13)
Allow the combustion to
stabilise. Do not insert probe to
avoid ‘flooding’ the analyser.

Perform Flue Integrity
Combustion Check

Insert the analyser probe into the
air inlet test point, allowing the
reading to stabilise.

Is O

2

20.6% and

CO

2

< 0.2% ?

Verify Flue Integrity

Indication that products of
combustion & inlet air are
mixing - further investigation is
required.
Check all flue components are
correctly assembled, fixed &
supported. Check the flue &
terminal are unobstructed.

Is O

2

20.6% and

CO

2

< 0.2% ?

TURN APPLIANCE OFF !

Call 0844 871 1555 for
advice.
The appliance MUST NOT be
commissioned until all
problems are identified and
resolved.

Check CO & Combustion Ratio
at Maximum Rate

Whilst the boiler is still
operating at maximum insert the
analyser probe into the flue gas
test point, allowing the reading to
stabilise.

Is CO < 350ppm
and CO/CO

2

ratio

< 0.004 ?

Verify Integrity of Seals

Check all burner seals, internal
flue seals, door & case seals.
Replace any seals that appear
unsound.

Is CO < 350ppm and
CO/CO

2

ratio <

0.004 ?

TURN APPLIANCE OFF !

Call 0844 871 1555 for advice.
The appliance MUST NOT be
commissioned until all
problems are identified and
resolved.
If commissioning cannot be fully
completed the appliance must be
disconnected from the gas supply
in accordance with the GSIUR.

Note:

Check & record the CO &

combustion ratio at both
maximum & minimum rates before
calling 0844 871 1555.

Set Boiler to Minimum Rate

(see 11.1.19)
Allow the combustion to
stabilise. Do not insert probe to
avoid ‘flooding’ the analyser.

Yes

No

No

Yes

No

Yes

Check CO & Combustion Ratio
at Minimum Rate

Whilst the boiler is
operating at minimum insert the
analyser probe into the flue gas
test point, allowing the reading to
stabilise.

Yes

No

Is CO < 350ppm and
CO/CO

2

ratio <

0.004 ?

No

Yes

BOILER OPERATING

SATISFACTORILY. NO

FURTHER ACTION

REQUIRED

Ensure test points are capped, the
boiler case front panel is correctly
fitted & secured and all other
commissioning procedures
completed.
Complete the ‘Benchmark’
Checklist, recording the CO &
combustion ratio readings as
required.

11.2

Checking Combustion

1. This procedure is mandatory in GB from April 2014. It is

strongly recommended to perform the procedure before that

date.

«
...
35
36
37
38
39
...
»

Summary of Contents for Titanium 24

































































Reviews:

No comments

Related manuals for Titanium 24

Brand: IDEAL Pages: 60

Brand: Raypak Pages: 76

Brand: Magikitch'n Pages: 18

Brand: Main Heating Pages: 83

Brand: Wells Pages: 30

MicoFlame Grande MFH2000

Brand: Camus Hydronics Pages: 36

ecoTEC exclusive 832

Brand: Vaillant Pages: 56

INSIEME EVO 32 B/100

Brand: Riello Pages: 16

INSIEME CONDENS 26 B

Brand: Riello Pages: 16

Brand: PEERLESS Pages: 17

Brand: PEERLESS Pages: 30

Brand: PEERLESS Pages: 40

Brand: eta Pages: 64

Brand: eta Pages: 68

Brand: eta Pages: 84

Brand: CleaverBrooks Pages: 70

Brand: CleaverBrooks Pages: 124

BRAVA ONE OF ErP

Brand: Sime Pages: 128

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands