Potensic Dreamer Pro User Manual Download Page 29

Page: 29 / 29

Reading Tips

Get Tutorials
Package List
Download PotensicPro App

Product Overview

Daily Maintenance
Drone Installation
Drone Diagram
Remote Control Diagram

About Aircraft

Aircraft Overview
Flight Mode
Intelligent Flight Modes
Return to home (RTH)
Drone Smart Battery
Charging Indicator Status

Remote Control

Remote Control Mode
Remote Control Charging
Remote Control Frequency Linking

Camera and Gimbal

Camera Overview
Support Micro SD Card
Gimbal Overview

PotensicPro APP

Operation Interface
Intelligent Flight Mode
Setting Interface

About Flight

Flight Environment Requirements
Flight Precautions
Connection Between the Remote Control and the Drone
Geomagnetic Calibration
Beginner Mode
Take-off and Landing
Emergency Stop

Appendix

Specification
Frequent Q&A
Safety Precautions
Warning and Tips
FCC Requirement

User manual x1

Drone with camera x1

Remote control x1

AC cable x1

Smart battery x1

Extra blades x 1 pair (CCW & CW)

Drone charger x1

USB charging cable x1

(for remote control)

*No signal return

*One Button Return:

*Low-power Return:

Drone

Camera

Remote control

Smart flight battery

Charger

Mode 1

Mode 2

Left stick

Right stick

Forward

Backward

Turn counterclockwise Turn clockwise

Move Left

Move right

Move Left

Move right

Upward

Downward

Right stick

Forward

Backward

Upward

Downward

Left stick

Register

After downloading the drone APP, it is necessary to register a personal account before using.

Register and log in

2. Intelligent Flight Mode

Lock / Unlock

GPS mode / Attitude mode

Headless mode / Head-hold

Circling mode

Waypoint mode

Follow me mode

Virtual control stick

Device is not connected properly

Restart drone and remote control.

Cannot unlock

Check if the drone is geomagnetic calibrated.

Cannot find GPS signal or GPS level drops

Check the surrounding environment of the
drone to see if there is high-frequency signal
interference.

The drone cannot return to home

Make sure there are no less than 6 GPS signal
show up on the App before take-off.

The drone jitters or video jitters

Can't take photos or record videos

a. Check if the propeller and motor shaft of
the drone are deformed or cracked, if yes,
please replace;
b. Check if screws are fixed in place after
disassembly.

a. Check if the drone is inserted with a Micro SD

card.
b. Check if Micro SD card format is correct.
c. Check if Micro SD card is full.

Problem

Solution

Reading Tips

Drone Diagram

2. Frequent Q&A

4. Warning and Tips

3. Safety Precautions

Download PotensicPro App

1. Daily Maintenance

Packing List

Picture

Picture 1

6. Charging Indicator Status

0%~25%

25%~50%

50%~75%

75%~100%

Fully charged

LED 1

LED 2

LED 3

LED 4

Current battery level

Flash state

Off state

Android users

iOS Users

For Android

For iOS

Contents

3.4 Waypoint Flight Mode

封底

单页尺寸：148x210mm

材质：105g书纸

工艺：骑马钉

印刷：单色印刷

Dreamer LED light

Motor

Camera

Blade

Front footlight

Rear footlight

Damping plate

Tripod

Pad

Gimbal

Gimbal clamp

Smart battery

Power indicator

Power switch (after short pressing once, long press for 2 seconds to switch on/off the drone)

Camera adjustment thumbwheel
Turn the thumbwheel to adjust shooting angle of the camera.

Photograph
Click to take one picture at a time.

Video-recording
Press once to record, click again to exit.

Camera brightness adjustment thumbwheel
Turn the thumbwheel to adjust the exposure of the camera.

Micro USB charging port

One-click take-off/landing
Press 2s to take off or land.

1. Specification

Appendix

About Flight

PotensicPro App

It is recommended that users watch the tutorial video first, and then read the "User Manual". Please

click the link or scean the QR code below to get tutorial videos.

Link:

https://www.youtube.com/channel/UCKjU1_4HmL0XAXng0J9-NCg

1. Use a soft clean cloth to clean the product.
2. Avoid exposure to the sun or heat.
3. Do not immerse this product in water, otherwise the electronic parts will be damaged.
4. Regularly check the plug and other accessories. If there is any damage, please stop using until it

is completely repaired.

Under normal flight conditions (flight altitude is greater than 5m), the drone will take the current position
as the circling center by default, with a radius of 10m and a speed of 3m/s, and circle clockwise.

Set multiple position points on the map, and the drone will fly in the order of set points(15 point at
most). The map will identify the serial number of each point.
The normal flight altitude is more than 5m, and the GPS signal is no less than 6. The drone flies to
designated points on the map in the sequence of the number of points in the shortest path, and hovers
at the last designated point.

Take-off weight: 820g ± 5g
Maximum ascending speed: 5 m/s (sport mode); 3m/s (standard mode)
Maximum descending speed: 2 m/s (sport mode); 2 m/s (standard mode)
Maximum horizontal flight speed: 8 m/s (sport mode); 5 m/s (standard mode)
Flight time: 28 minutes
Working environment temperature: 0° C-40 ° C
GPS: GPS+GLONASS
Working frequency: 5.725-5.850GHz
Transmission power:5.8GHz: <24 dBm
Hovering precision (vertical): ±0.5 (when GPS works normally)
Hovering precision (horizontal): ±1.5m (when GPS works normally)

Image sensor: 1/3-inch Sony CMOS; 16MP
Lens: FOV 78°
Picture maximum resolution: 4608x3456
Photo shooting mode: single photo
Lens rotation range: +0°-90°
Video resolution: 3840×2160@30fps
Maximum video storage code stream: 60Mbps
Supporting file system: FAT32
Image format: JPEG
Video format: MP4 (AVC/H.264)
Micro SD card: 4-256GB with transmission speed of class10 and above.
Working environment temperature: 0°C~40°C

Rated input: 100-240V~50/60Hz, 1A
Rated output: 17.5V, 1.5A
Rated power: 26.25 W

Working frequency: 5.725-5.850GHz
Maximum effective distance of signal: 2000m (no interference or blocking)
Working environment temperature: 0°C~40°C
Battery: 2800mAh lithium battery
Equivalent isotropic radiation power (EIRP): 5.8GHz: <24 dBm
Working voltage/current: 3.7V/1.2A

Capacity: 3000mAh
Voltage: 15.2V
Battery type: Li Po 4S
Capacity: 45.6Wh
Overall weight of battery: 335g
Working environment temperature: 0° ~ 40°C
Maximum charging power: 26.25W

Keep away from people when flying the remote-controlled drone. Improper assembly or damage to
the body, poor electronic control, and unfamiliar operation may lead to unpredictable accidents such
as drone damage or personal injury. Operators should pay attention to flight safety, and understand
responsibilities caused by negligence.

1. The package and instructions contain important information and should be properly kept.
2. It is your responsibility to ensure that this drone will not cause injury and property loss.
3. The commissioning and installation of the drone shall be carried out in strict accordance with operation

instructions. The drone shall keep a distance of 1-2 meters from users or other people during fly to avoid

the drone from colliding with heads, faces and bodies of people during fly and landing.

4. Our company and retailers shall not be responsible for any loss, damage and human injury caused by

improper use or operation.

5. Adults should provide guidance on children when flying. Children under 14 years old are not allowed to

operate this product.

6. Please install and use correctly according to instructions or packaging requirements. Some parts shall be

assembled by adults.

7. This product contains small parts, please keep it out of reach of children to prevent dangers of eating or

suffocation.

8. It is strictly forbidden to fly on the road or in water-gathered places to avoid accidents.
9. Please put packing materials away in time to avoid causing harm to children.

When normal flight altitude is above 5m, and GPS signal is no less than 6, the drone will follow move
position of mobile phone. In follow me mode, the drone can fly beyond the maximum distance limit.

Click the icon to enter circle flight mode

Click the icon to start the waypoint flight mode.

Click Icon to activate follow me mode.

Long press the "home" button on the remote control for 1 second or click the "home" icon on the
app to start the one button return, the remote control emits the continuous "beep" sound, then the
aircraft will return. Press the "home" key for 1 second or click the icon “x” to cancel the return flight and
exit the return flight automatically. The "beep" sound disappears.

If the drone lose its connection to the remote control, it will automatically enter the return mode. The
drone will automatically return to the ground, If the drone and the remote control are reconnected
during return. The drone will hover at this time, and the operator can control it again.

Note:

The drone does not have automatic obstacle avoidance function. If the drone crashes into

buildings or other obstacles on the way back, it will fall and break.

This chapter mainly introduces the functional features of Dreamer Pro, guides on how to install the
aircraft, and introduces the names of various parts of the aircraft and remote control.
Thank you for purchasing Potensic Dreamer Pro drone. Please read the user manual carefully and
keep it for future reference. If you need help, please contact our support team

([email protected])

with your order number from Amazon or official website.
Potensic Dreamer Pro is equipped with an intelligent flight control system. The integrated gimbal is
located under the fuselage. Dreamer Pro can realize functions such as Waypoint flight, intelligent
following, and automatic return to home. 5.8G image transmission is integrated inside the remote
control for image transmission.
The drone camera adopts a 1/3-inch Sony CMOS image sensor and a gimbal stabilization system to
stably shoot a 4K high-definition video with 30 frames per second and 16MP photos.

Make sure the propellers are installed correctly and tightly.

Remote Control Diagram

3. Intelligent Flight Modes

About Aicraft

Know Your Remote Control

Antenna

Control stick

Dreamer Pro uses a 5.8G remote control with complete function buttons. It can support various
operations and settings of the drone and camera within a maximum communication distance of
2000m, and can display real-time HD pictures on the mobile device through PotensicPro app. The
remote control has a built-in rechargeable lithium battery, which can work continuously for up to
2.5hours.

Note

Please return in time and charge the battery when the drone in low battery. Connect the adapter
correctly as shown in the figure to charge. The indicator flashes when charging, and goes out when
fully charged. It takes about 2 hours.

1. Please use the original charger to charge.
2. Do not charge on a carpet to avoid fire.
3. Recharge every 3 months to keep battery active.
4. Do not put a charged battery under high temperature, such as open fire or electric heating

device, otherwise it will be damaged or explode.

5. Do not strike or knock surface of hard objects with a battery.
6. Do not disassemble a battery.
7. Do not leave the battery alone during charging.

Note: When hearing a "click" sound, the battery is successfully installed in place.

2.3. Installation and removal of battery

Picture 1

Picture 2

Insert the battery in the right direction as shown in Picture 1.
Press the left and right sides of the battery and pull out the battery as shown in Picture 2.

2.4 App Real-time Image Connecting

(The plug is not included in packing list)

Please search and download the drone App "PotensicPro" in Google Play or scan the QR code below
to download. This App is compatible with Android 5.0 and above.

Please search and download the drone App "PotensicPro" in APP store or scan the QR code below
to download. This App is compatible with IOS 9.0 and above.

Fill in email - fill in password - view agreement - click register. Please log in after successful
registration. (Note: Please keep your mobile phone connected with network during registration)

Tel: 858-222-1895
Web: www.potensic.com
FB: www.facebook.com/Potensic

Email: [email protected](USA)
Email: [email protected](CA)
Email: [email protected](UK)

Dreamer Pro

User Manual

DANGER

Only suitable

for age 14+

Product Overview

Remote Control

Get Tutorials

Micro USB adapter x3

2.2 Propeller Installation

1.When installing blades, pay attention to the "CW" and "CCW" marks on the blades.

2.Press down the blade in alignment with the central axis, and rotate according to the lock marked

direction by the blade lock until it is fully screwed. After installation, the propeller will pop up and
lock. Removal of the blades are reverse of the above steps.

3.3 Follow Me Mode

4. Return to Home (RTH)

The aircraft has the function of automatic return. The takeoff point is the home point of the aircraft. The
intelligent return (RTH) function enables the aircraft to return to the home point. There are three types of
aircraft return (RTH): one button return / intelligent low power return / no signal return. When the flight
altitude is less than 20 meters, the aircraft rises to 20 meters before returning. When the flight altitude is
more than 20 meters, and the aircraft will return with current altitude.

Low-power alarm: when power of the drone is less than 20%, there is continuous "beep" sound from the
remote control and the battery icon on the App flashes.
Low-power return: the drone system will automatically determine whether to return according to the
distance and battery power. When the drone returns, its four footlights remain flashing until it lands on
the ground, and the remote control emits the continuous "beep" sound. The Power will be 8%-12% left.

5. Drone Smart Battery

1. Remote Control Mode

There are two remote control modes of this product, mode 1 and mode 2.
Mode 1 is the default setting.

2. Remote Control Charging

Camera and Gimbal

3. Remote Control Frequency Linking

Connect the remote controller's Micro USB port to the commonly used 5V2A charger to charge, it
takes about 2 hours to fully charge.

This chapter introduces flight environment requirements, precautions, and flight operation procedures.

1. Flight Environment Requirements

1. Please do not fly in bad weather, such as strong wind (wind speed 5 and above), snow, rain, foggy

weather, etc.

2. Choose an open place without surrounding tall buildings as the flight site. Buildings that use a lot of

steel will affect the geomagnetic work, and will block the GPS signal, resulting in poor positioning of
the aircraft or even unable to locate.

3. When flying, please keep your eyes in control and keep away from obstacles and crowds.
4. Please do not fly in areas with high voltage lines, communication base stations or transmission

towers to avoid interference from the remote control.

5. Flying above 5000 meters above sea level, due to environmental factors, the performance of the

aircraft battery and power system will be degraded, and the flight performance will be affected.
Please fly with caution.

2. Flight Precautions

4. Geomagnetic Calibration

1. Check whether the remote controller, intelligent flight battery and mobile device have sufficient

power.

2. Check whether the fuselage is complete and the propeller is correctly installed.
3. Check whether the camera works normally after the power is turned on.
4. Check if the App is running normally.
5. Check if the SD card is inserted, make sure the camera is clean.
6. Low battery protection: Low battery alarm is triggered when the power is less than 20%. Based on

the distance between the current position and the Home point, the aircraft will intelligently trigger a
low-power return.

7. Loss of connection protection: It is triggered after 3 seconds of loss of connection; the re-connection

is successful during the return flight, and it can be canceled manually.

8. Out-of-control protection: After the aircraft's horizontal tilt angle is over 80 degrees for 2 seconds,

the motor will automatically stop.

Step 1:

Enter the PotensicPro App setting interface, click the second column, and select geomagnetic

calibration in thelist, then click"Star Calibration" on the right side. The left front light flashes

green and the left rear light flashes red indicate that it's ready for calibration.

Step 2:

Rotate the drone 720° horizontally, than the right front light flashes green and right rear light

flashes red. (Picture 1)

Step 3:

Rotate the drone 720° vertically with camera upwards. The four indicator light are solid on(the

2 front lights are green while the rear lights are red), and calibration is completed. (Picture 2)

If no less than 6 satellites are searched by the drone, the 2 front lights are stably on, and the 2

rear lights flash slowly. Then, the drone can take off.

Picture

5. Beginner Mode

The beginner mode is in default. Under the beginner mode:
A. The flight distance is limited to 0 ~ 30m
B. The flight altitude is limited to 0-30m

6. Take-off and Landing

Manually take off: Push the left and right stick inwards 45 degrees(Picture 1) at the same time,
unlock the drone or click the App unlock icon , and push up the throttle lever.
One button take off: Long press the "take-off and land" button for 2 seconds, there will be a short
"beep" sound, or click the icon on the App, the drone will slowly take off and hover at a height of
about 1.2 meters.

Manually landing: Pull down the throttle stick. After the aircraft lands on the ground, push the throttle
stick to the lowest position and hold it for 3 seconds, the motor will stop.
Auto landing: Click " " and confirm the safe landing conditions, slide the button to the right to
start the automatic landing. After landing on the ground, the motor will automatically stop.
During the descent of the aircraft, the user can exit the automatic landing process by clicking the x
button on the App interface.

7. Emergency Stop

Press the left and right joysticks simultaneously for 1 second.
Note: Stopping the motor in the air will cause the aircraft to crash. It is only used in special situations
(such as the aircraft may hit the crowd) to urgently stop the motor to minimize injuries.

10. Do not dismantle or modify the drone, which may cause failure.
11. The battery of charger battery box shall be plugged into the specified power source as marked on the

product.

12. The remote control has a built-in lithium battery, which does not need to be replaced.
13. Use only the original charger.
14. The charger is not a toy.
15. The remote control uses a 3.7V built-in lithium battery.
16. When charging the rechargeable battery, it shall be carried out under the supervision of an adult. When

charging, it is necessary to keep away from flammable materials. The guardian should not leave the

drone outside the surveillance range during charging

17. Please do not short circuit or squeeze the battery to avoid explosion.
18. Do not mix different types of lithium batteries.
19. The drone uses a smart lithium battery, which can be recharged when plugged in or out.
20. Do not short-circuit, decompose or put the battery into a fire; do not place the battery in a high tempera-

ture and hot place (such as in a fire or near electric heating devices).

21. The drone shall be used far away from other electrical equipment and magnetic objects to avoid mutual

interference.

22. Please keep a safe distance from propellers rotating at a high speed to avoid dangers of wringing and

cutting.

23. Keep the model away from ears! Misuse may cause hearing loss.
24. Please use a micro USB 5V charger instead of higher voltage charger.
25. In order to ensure requirements for magnetic environment of the aviation radio station. The use of model

remote control shall be stopped as required within periods and areas of radio control orders by relevant

national departments.

26. Keep your drone in line of sight.
27. Don't fly in the crowd.
28. Do not fly over sports venues or events.
29. Please totally learn about airspace restrictions and requirements.

Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

5. FCC Requirement

Warning: Battery charging shall always need
supervision by an adult. Unplug the
battery when it is fully charged. Do not
overcharge.

Warning: This product can only be used by
adults or children above 14 years old.
Children under 14 years old need
supervision by an adult

Name
Model
Battery voltage
Manufacturer

Address

Dreamer Pro

DSDR01C

15.2V

DeepSea Innovation Co., LTD

Capacity: 3000mAh

，

45.6Wh

Input

：

100-240V

，

50/60Hz 1.0A

Output

：

17.5V-1.5A

Adapter information

3rd Floor, Building 4, Silicon Valley
Courtyard, Qingquan Road, Shenzhen, CN

Battery information

EC REP

: DST Co., Ltd.

Fifth Floor 3 Gower Street,London,WC1E 6HA,UK

Made in China

Drone status

Standard mode/Sport mode

Return to the menu

Head mode/Headless mode

Lock/Unlock

GPS mode/Attitude mode

GPS signal level

Transmission signal level

Drone power

Setting interface

Photo Taking/Video Recording

Camera setting

Photo/Video switch

Camera pitch adjustment

Vertical flight speed

Distance

Flight height

Horizontal flight speed

Altitude ball/map

Intelligent flight mode settings

One-click return

One-click take-off/one-click landing

3. Setting Interface

Calibration settings

Remote control settings

Main controller settings

About smart batteries

QR Code

Power switch
Press 2s to turn the remote control on/off.

Control sticks storage box
A box to place control sticks.

(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environ-
ment. This equipment should be installed and operated with a minimum distance of 20cm between
the radiator & your body. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.

Note:

This product has been tested to meet requirements of FCC Part 15 for Class B digital products. These
regulations ensure that this product will not have a harmful impact on the residential environment
during installation and use. This product will radiate RF energy when working. If not installed and used
according to instructions, it may cause interference to wireless communication.

● However, in some specific installation and use occasions, there may be interference. Users can

determine whether interference is caused by the product by switching on and off. If this product does
interfere with wireless and video receiving equipment, users may take the following corrective
measures:
• Adjust the orientation of the receiving antenna appropriately.
• Increase distance between the product and receiving equipment
• Connect the device to a socket with a different circuit from the receiver.
• Seek assistance from a dealer or an experienced wireless / video technician.

● The manufacturer shall not be responsible for any wireless and video interference caused by illegal

modification of the equipment. Because these modifications and changes are beyond the user's
operation permission.

3. In order to properly use this product, please use original parts for modification or maintenance to

ensure flight safety. Please operate and use this product to the extent permitted by its functions,
and it shall not be used for illegal purposes beyond safety laws and regulations.

4. Avoid flying alone

It is difficult to learn control skills of the drone in the early stage. It is necessary to avoid flying alone
as much as possible, and needs instruction of experienced operators.

5. Safe operation

Please operate the remote controlled drone according to your own status and flight skills. Fatigue,
poor mental state or improper operation will increase the probability of accident risks.

6. Keep away from high-speed rotating parts.

When the drone rotor is rotating at high speed, keep operators, surrounding people and objects
away from rotating parts to avoid danger and damage.

7. Keep away from heat source

The remote controlled drone is composed of metal, fiber, plastic, electronic components and other
materials. Therefore, it is necessary to keep away from the heat source as far as possible, prevent
sunlight, avoid deformation or even damage due to high temperature.

1. Keep away from obstacles and people

The remote controlled drone is uncertain in flight speed and state during fly, which poses potential
danger. It shall be far away from people, high-rise buildings, high-voltage wires, etc. during fly, and
avoid flying in the bad weather such as wind and rain, thunder and lightning, to ensure safety of
operator / surrounding people and property.

2. Keep away from humid environment

The interior of the drone is composed of many precise electronic components and mechanical parts.
Therefore, it is necessary to protect the drone from humidity or prevent water entering the body, to
avoid accidents caused by the failure of mechanical and electronic components.

20200622

伍丽

日期：

英文说明书

1:1

V01

制作人：

文件名称：

品牌名称：

文件种类：

单位：

产品型号：

P1 Pro

版本

比例：

深海集团

C.01.006.00022V01

2.1. Gimbal Lock

Hold the fixed camera with one hand, and remove the gimbal clamp with the other hand in the
direction of the arrow shown as Pic.

Unlock Direction

Lock Direction

Follow these steps to connect your mobile device:
1. Expand and adjust the antenna position.
2. Open the remote control pull-out board, and then put your mobile phone into it. The size range of

the clamping machine is 97-178mm

3. Use the corresponding connecting cable to connect the mobile device to the micro USB interface of

the remote control.

One-click return
By pressing the button for 1s, the drone will perform auto returning after you hearing one
beep sound from the remote control; press it again and also hear one beep sound, then the
drone will stop the returning.

Standard Mode/Sport Mode
Push the button to the right side position to start sport mode, The standard mode is 5m/s
and the sport mode is 8m/s.

Dreamer Pro uses a 5.8G remote control with complete function buttons. It can support various
operations and settings of the drone and camera within a maximum communication distance of
1000m, and can display real-time HD pictures on the mobile device through PotensicPro app. The
remote control has a built-in rechargeable lithium battery, which can work continuously for up to 3
hours.

If you replace the remote control, it is necessary to follow the below steps to re-connect the new
remote control and the drone.

1.Install the drone battery; short press the power button once, then quickly long press it for 7s, the

drone 2 front LED foot lights and 2 rear lights start quick flashing alternately;

2.Press down the remote controller’s right joystick and power button for 2s, then the remote controller

emit 2 beep sounds, and its power indicator is quickly flashing.

3.Then the remote controller and the drone enters auto linking status, please wait about 30s, the

remote controller will emit one beep sound and its power indicator is stably on, the drone 4 foot lights
are quickly flashing, 10s later, the 4 foot lights keep stable bright, which means the frequency linking
is completed.

2. Drone Installation

(1)

(2)

(3)

Geomagnetic calibration is required for the first flight (after once calibration, the same region within

300km doesn't need calibration). If the geomagnetism of the aircraft is disturbed, the manual

re-calibration may need to done to the drone.

Note:

If the left front light flashes green and the left rear light flashes red slowly, it indicates that

calibration fails. It is recommended to recalibrate geomagnetic after changing the take-off location

1. Aircraft Overview

Dreamer Pro is mainly composed of flight control, communication system, positioning system, power
system and smart battery. In this chapter, the functions of various components on the aircraft are
described in detail.

2. Flight Modes

Dreamer Pro adopts a new generation of Potensic flight control, which supports the following two flight
modes:
GPS mode: Use GPS module to achieve precise hovering, waypoint flight and other intelligent flight
modes. In GPS mode, the GPS signal is good, the GPS can be used for accurate positioning; when
the GPS signal is not good, the aircraft cannot be accurately positioned, it only provides attitude
stabilization, and does not support the intelligent flight function.
Attitude mode: The GPS module is not used, only the stabilization of the altitude is provided, so that it
will drift in the horizontal direction. At this time, the operator needs to manually control the flight of the
aircraft. This mode is used by novices with caution. In this mode, the difficulty of controlling the aircraft
will be greatly increased. If you want to use this mode, you must be familiar with the behavior of the
aircraft in this mode and be able to skillfully control the aircraft. Do not fly the aircraft out of a long
distance during use, so as not to lose Judging the attitude of the aircraft poses risks.
Two Modes Switching: The default GPS mode is turned on, you can press the middle button of the left
joystick during flight or switch in the App function module.

Drone Indicator Status

3.1 Headless Mode

After take-off, the headless mode can be started only when the flight distance is more than 10 meters.
Click the headless mode icon in app to enter headless mode, and then click once again to exit
headless mode and the drone will land on the ground to automatically.
In headless mode (take Mode 1 as an example), when you push the right control stick backward, the
drone will fly near to the Home Point(take-off point); when you push the right control stick forward, the
drone will fly away from the Home Point(take-off point); when you push the right control stick to the
left / right, the drone will fly circle counter clockwise / clockwise around the home point.

3.2 Circle Flight

1. Camera Overview

The Dreamer Pro adopts a 1/3-inch CMOS Sony sensor with 16MP camera. Equipped with low
distortion wide-angle lens. The blue glass filter can effectively improve the picture quality. Standard UV
lens to protect the lens. When recording video, Dreamer Pro supports 4K ultra-high-definition video
recording at up to 30 frames per second, providing 4 times the full HD resolution of image details.
Support MPEG-4 AVC (H.264) format, and can achieve high-quality video recording with a high bit rate
of 60Mbps.

2. Support Micro SD Card

* Insert micro SD card with the metal side up

3. Gimbal Overview

The three-axis stable gimbal provides a stable platform for the camera, so that the camera can also
shoot a stable picture even when the aircraft is flying at high speed. The pitch angle can be adjusted
via the gimbal dial on the remote control, and the camera can also be adjusted by sliding the camera
pitch adjustment slider on the main interface of the PotensicPro APP. The controllable angle of the
pitch direction is -90° to 0°.

Attitude Mode

GPS Mode

Four lights always on

Front lights always on

Rear lights blink slowly

Headless Mode

Front lights blink slowly

Rear lights always on

Warning and Abnormal

Drone Low Power

Drone Disconnected

Drone Binding

Emergency Stop or Rollover(Motor stopped)

Firmware Upgrade

Sensor Abnormal

Four lights blink slowly

Four lights blink quickly

Left and right side lights blink alternately

Horizontal calibration: left lights blink slowly, right lights keep on

Vertical calibration: left lights keep on, right lights blink slowly

Four lights keep long off, short on cycling

Four lights on in turn clockwise

Rear left and right lights blink alternately

Geomagnetic Calibration

Insert the micro SD card into the camera SD card slot. It is recommended to use SD card products of
class10 or above, brand such as SanDisk, Kingston or Samsung, which require a minimum SD card
capacity of 4GB and a maximum of 256GB. All pictures and video files will only be recorded on SD
card, instead of storing in the App or your phone. Upload to your phone from the photo album. The
product package list does not include SD card.

Because the remote control and the aircraft have completed frequency linking before leaving the
factory, they can be connected directly.

3. Connection Between the Remote Control and the Drone

1.Install the drone battery; click the power button once, then quickly press it for 2s to turn on the

drone; the battery indicator will light, the drone will emit beep sound and its 4 LED foot lights start
quick flashing;

2.Press the power button of the remoter controller for 2s, then the remote controller emit 2 beep

sound and the indicator lights up;

3.Please wait about 35s, the 4 LED foot lights on the drone will stably light, which means it is done.

1. Operation Interface