Portwell PEB-7431VL User Manual Download Page 47

Page: 47 / 55

BIOS Setup Information

PEB-7431VL User’s Manual

4-22

Note

When this error appears, the system will boot in ISA mode, which allows you to
run the EISA Configuration Utility.

FLOPPY DISK(S) fail (80)

→

Unable to reset floppy subsystem.

FLOPPY DISK(S) fail (40)

→

Floppy Type dismatch.

Hard Disk(s) fail (80)

→

HDD reset failed

Hard Disk(s) fail (40)

→

HDD controller diagnostics failed.

Hard Disk(s) fail (20)

→

HDD initialization error.

Hard Disk(s) fail (10)

→

Unable to recalibrate fixed disk.

Hard Disk(s) fail (08)

→

Sector Verify failed.

Keyboard is locked out - Unlock the key.

Keyboard error or no keyboard present.

Cannot initialize the keyboard. Make sure the keyboard is attached correctly
and no keys are being pressed during the boot.

BIOS ROM checksum error - System halted.

The checksum of ROM address F0000H-FFFFFH is bad.

Memory test fail.

BIOS reports the memory test fail if the onboard memory is tested error.

Summary of Contents for PEB-7431VL
























































Search results

Summary of Contents for PEB-7431VL

Reviews:

Related manuals for PEB-7431VL

Brands by name

Popular brands

Portwell PEB-7431VL, User Manual

Search results

Summary of Contents for PEB-7431VL

Reviews:

Related manuals for PEB-7431VL

Brands by name

Popular brands