manualshive.com logo in svg

POP UP PUSH 10 PRO, Operator'S Safety And Maintenance Handbook

Share
Download
POP UP PUSH 10 PRO Operator'S Safety And Maintenance Handbook Download Page 5

Page 4

PUSH PRO -0120843

INTRODUCTION

This manual covers the PUSH 6 PRO, PUSH 8 PRO, and PUSH 10 PRO Aerial Work Platforms. This manual must be 
stored on the machine at all times.

Read, understand and follow all safety rules and operating instructions before attempting to operate the 
machine. 

When contacting Pop Up for service or parts information, be sure to include the MODEL and SERIAL NUMBERS 
from the equipment nameplate. Should the nameplate be missing, the SERIAL NUMBER is also stamped on the 
front of the chassis.

COMPONENT IDENTIFICATION

RIGHT SIDE

REAR

Platform

Upper Controls

Operators Manual

Component Tray

Hydraulic Reservoir/
Pump and Batteries

Forklift Pocket

Lower Controls

Entry Gate

Guardrails

Toeboards

Scissors Structure

Chassis

Safety Prop

One on Each Side

Forklift Pocket

Brake Lever

Battery Charge 
Indicator

Emergency 
Lowering Lever

Nameplate

Summary of Contents for PUSH 10 PRO





















Reviews:

No comments

Brands by name

Popular brands

Load more brands