Ponsel ACTEON 2000 Series User Manual Download Page 33

Page: 33 / 67

User manual

PONSEL

Référence : NOTICE_ACTEON_2050_v001

V : 002

33/67

6.1.6 Adjusting the temperature sensor slope:

If you observe a small measurement error, you may only adjust the slope of your sensor by carrying out the
following procedure:

Use the

and

keys to select

the type of calibration and the
probe to be calibrated.

Select the

Gain adjust

menu of the temperature sensor and

press ENTER.

Use the

and

keys to adjust the

ambient water temperature value.

Press the ENTER key to confirm slope
adjustment.

CALIBRATION

DU TEMPERATURE SENSOR

Immerse the sensor in
water at ambient temperature

Standard:
Measure:

°C
°C

20.00

20.20

WAIT: Nonstable measurement

AWAIT MEASUREMENT STABILISATION

Immerse the sensor in water at ambient temperature.

ESC: Leave the current slope
ENTER: Validate the new slope

ENTER : Validate the choice

CALIBRATION

SENSORS CALIBRATION

SS SENSOR

Gain adjust

Immediate calibration

Differed calibration

Theoretical calibration

TEMPERATURE SENSOR

Gain adjust

Complete calibration

Theoretical calibration

ENTER: Validate the choice

Summary of Contents for ACTEON 2000 Series




































































Search results

Summary of Contents for ACTEON 2000 Series

Reviews:

Related manuals for ACTEON 2000 Series

Brands by name

Popular brands

Ponsel ACTEON 2000 Series, User Manual

Search results

Summary of Contents for ACTEON 2000 Series

Reviews:

Related manuals for ACTEON 2000 Series

Brands by name

Popular brands