background image

110-031 PSC/EN

5

LCD Display

Keypad

High Limit Warning 

Indicator

Flashes if you 

attempt to enter a 

set point higher than 

the High Limit value. 

Lit steady when High 

Limit value is being 

set 

Heating Symbol

Lit when heater is 

active

Fault / Warning 

Symbol

Lit when fault or 

warning condition is 

detected

Set Point Indicator

Flashes when 

set point is being 

changed; lit steady 

during normal 

operation

Timer Symbol

Lit when timer 

is being set or 

is in use

Over-Temperature / 

Low Liquid Symbol

Lit when over-

temperature or low 

liquid level fault is 

detected

Calibration Mode 

Indicators

Lit when unit 

calibration offset is 

being set

Version Indicator

Lit when firmware 

version ID is being 

displayed on the 

lower readout

Temperature Unit 

Symbol

Shows 

temperature unit in 

use when lit

Upper Readout

Displays actual 

bath temperature

Lower Readout

Displays set point 

temperature 

during normal 

operation; displays 

operational 

information when 

Menu button is 

pressed

Temperature 

Resets Indicator

Lit when preset 

is being set or is 

in use

Loss of Power 

Indicator

Lit when electrical 

power is restored 

after power disruption

Power Button

Turns power to 

the Controller On 

and Off

Timer Button

Used to start 

and stop the 

timer

Selection Buttons

Used to increase 

or decrease 

temperature 

settings and 

operational 

parameters

Temperature 

Preset Buttons

Used to select 

frequently used 

user-defined 

set point 

temperatures

Menu Button

Used to select and set various 

operational parameters

www.calcert.com

[email protected]

1.888.610.7664

0

5

10

15

20

25

30

Summary of Contents for WBE10A11B























Reviews: