background image

110-031 PSC/EN

1

Table of Contents

Introduction  ........................................................................................... 2

General Safety Information  .............................................................. 2

Safety Recommendations  ................................................................ 3

Regulatory Compliance & Testing  .................................................... 4

Unpacking Your Water Bath  ............................................................. 4 

Contents  ........................................................................................... 4

LCD Display  ..................................................................................... 5

Keypad  ............................................................................................. 5

Installation and Startup ......................................................................... 6

General Site Requirements ............................................................... 6

Adding Liquid to the Reservoir .......................................................... 6

Electrical Power ................................................................................ 8

Controller Setup ................................................................................ 8

Power On .......................................................................................... 8

Selecting the Temperature Unit ........................................................ 8

Setting the High Limit Value .............................................................. 9

Setting the Temperature Presets ...................................................... 9

Normal Operation .................................................................................10

Keypad Controls ...............................................................................10

Turning Your Water Bath ON ............................................................10

Adjusting the Set Point Temperature ................................................10

Setting and Using the Timer ............................................................. 11

Using the Temperature Presets ........................................................11

Entering a Calibration Offset ............................................................12

Resetting the Factory Default Values ...............................................13

Loss of Power Restart ......................................................................13

Displaying the Firmware Version ......................................................13

Display Messages and Alarms ............................................................14

Routine Maintenance & Troubleshooting ...........................................15

Draining the Bath Reservoir .............................................................15

Resetting the Over Temperature / Low Liquid Level Safety .............15

Cleaning the Bath ............................................................................16

Troubleshooting Chart ......................................................................16

Technical Information ..........................................................................17

Performance Specifications

 .............................................................17

Reservoir Fluids ...............................................................................18

Application Notes .............................................................................19

Equipment Disposal (WEEE Directive) ...............................................20

Service and Technical Support ...........................................................21

Warranty ................................................................................................21

www.calcert.com

[email protected]

1.888.610.7664

0

5

10

15

20

25

30

Summary of Contents for WBE10A11B























Reviews: