background image

14

110-031 PSC/EN

Display Messages and Alarms

Symbol and/or Word

Description

Comments/Corrective Action

HIGH LIMIT

(flashing)

Warning

: The operator is attempting 

to enter temperature set point that 

is above the High Limit temperature 

value.

Increase the High Limit temperature value or 

decrease the set point temperature.

Fault

: The liquid in the bath has 

dropped too low or the temperature 

of the bath fluid has exceeded the 

Safety Set temperature. Power to 

the heater will remain Off until the 

over-temperature thermostat resets.

Fluid level in the reservoir has fallen below 

minimum level; remove power, allow bath to 

come to room temperature and add fluid.

Fluid temperature is higher than one or 

both Over-Temperature Safety thermostats. 

Remove power and allow bath to come to room 

temperature; if problem persists, consult factory.
Controller failure; consult factory.

CALIBRATION 

OFFSET

(flashing)

Warning

: The operator is attempting 

to enter a Calibration  Offset value 

without first performing the proper 

power down/power up sequence.

Place Mains Switch on rear of unit in Off 
position. Press and hold        while returning 
Mains Switch to On position. Release        when 
unit enters Standby mode.

Press        on keypad and then press        until 
CALIBRATION OFFSET appears on LCD.

POWER FAIL

Informational

: Indicates that there 

was a loss of electrical power during 

operation.

Press        to turn the Water Bath Off and then 
back On. This will clear the message.

SET

(flashing)

Informational

: Indicates that the 

temperature set point is being 

changed.

Press 

    

or

     

until desired set point 

temperature is displayed on lower readout. 
Press

     

or allow the display to timeout to 

accept.

°C or °F

on lower readout.

Informational

: Indicates that the 

temperature unit is being changed.

Press

     

to change ºC to ºF; press 

    

to 

change ºF to ºC. Press

     

or allow the display 

to timeout to accept.

TIMER

Informational

: Indicates that the 

timer is being set.

Use the 

    

or

     

buttons to increase/ 

decrease the time duration. Press  

    

or allow 

the display to timeout to accept.

HIGH LIMIT

(steady)

Informational

: Indicates that the 

high limit value is being changed. 

 

 

 

Warning

: Indicates that the bath 

temperature has exceeded the high 

limit value for more than 5 seconds.

Press 

    

or

     

until desired high limit  

temperature is displayed on lower readout. 
Press

     

or allow the display to timeout to 

accept.

 
Allow bath temperature to fall below the High 
Limit Value. 
Place unit in Standby mode and press         to 
return from Standby mode. Reset factory default 
values

CALIBRATION 

OFFSET

(steady)

Informational

: Indicates that the 

calibration offset value is being 

changed.

Press 

    

or

     

until desired calibration offset 

is displayed on lower readout. Press

     

or 

allow the display to timeout to accept.

PRESET

1, 2 or 3

Informational

: Indicates that the 

bath is operating using the indicated 

Preset set point temperature and 

timer (optional) values.

No action required.

TIMER

Informational

: Indicates that the 

timer is being used.

Press and release

     

to pause timer. Press 

and hold

     

for two seconds to reset to 00:00.

Informational

: Indicates that heat is 

being applied to the bath.

This symbol is lit steady while the bath is 

heating to the set point temperature and 

flashes when the set point temperature is being 

maintained.

!

www.calcert.com

[email protected]

1.888.610.7664

0

5

10

15

20

25

30

Summary of Contents for WBE10A11B























Reviews: