Polar Air PP05H080I1 Operating Instructions Manual Download | Manualshive

Page: 23 / 40

background image

Operating Instructions

Be sure all operators and others around the compressor and its controls comply with all applicable OSHA, Federal,
State and Local regulations, codes and standards relating to personal protective equipment. This includes respiratory
protective equipment, protection for the extremities, protective clothing, protective shields and barriers, electrical
protective equipment, and personal hearing protective equipment.

2.

DO NOT

use air line anti-icer systems in air lines supplying respirators or other equipment used to produce

breathable air.

DO NOT

discharge air from these systems in unventilated or other confined areas.

1.

Install compressor pump in a clean, dry and well-lit area. Be sure installation area can maintain a

temperature range between 35˚ - 110˚ F.

2. Insulate cold water or other low temperature pipes that pass overhead to avoid condensation dripping on

compressor which could cause rust and/or motor shorting

Inspect compressor pump prior to any use. Check for external damage that
might have occurred during transit. Be careful of moving parts then test
pulley by turning it freely by hand.

Report any damage to delivery carrier

immediately.

WARNING

Do not operate unit if damaged during shipping, handling or use.
Damage may result in bursting and cause injury or property damage.

WARNING

DO NOT install compressor in boiler room, paint spray room, or area
where sandblasting occurs. Make sure inlet air is away from exhaust
fumes or other toxic, noxious or corrosive fumes or substances.

DANGER

Personal Protective Equipment

Inspection

Installation

Area

4

«
...
21
22
23
24
25
...
»

Summary of Contents for PP05H080I1









































Reviews:

No comments

Related manuals for PP05H080I1

Brand: Parkside Pages: 72

Brand: Parkside Pages: 60

Brand: Parkside Pages: 44

Brand: Super Ego Pages: 8

Brand: ULTIMATE SPEED Pages: 122

Brand: Tamiya Pages: 8

Brand: Hamron Pages: 12

Brand: DV Systems Pages: 37

Brand: LA Audio Pages: 2

Brand: Vector Pages: 16

Brand: Atlas Copco Pages: 75

Brand: Proxxon Pages: 30

Brand: Scarlett Pages: 14

Brand: Atlas Copco Pages: 138

Brand: Easylife Pages: 2

Brand: Campbell Hausfeld Pages: 20

Brand: NATI Pages: 8

Brand: Campbell Hausfeld Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands