Polar Air PP05H080I1 Operating Instructions Manual Download | Manualshive

Page: 12 / 40

background image

Operating Instructions

12

9. Make sure proper overload protection for the motor is installed.

1.

Connect first power lead to 1L1.

2. Connect second power lead to 3L2.
3. Connect ground wire to existing motor ground wire.

1.

Connect first power lead to 1L1. Leave existing jumper

wire installed. See Figure 6.

2. Connect second power lead to 3L2. Leave existing

jumper wire installed.

3. Connect ground wire to ground lug.

4. Ensure all wiring and terminals are properly tightened.

Install power leads into terminals opposite motor wires.

Ensure power supply and internal wiring is adequate according to voltage and frequency stated on motor nameplate
and starter. Voltage should not vary more than 12% to ensure proper operation of compressor.

DANGER

Improperly grounded electrical components are shock hazards. Make
sure all the components are properly grounded to prevent death or
serious injury.

When wiring unit with magnetic starter, do not install power directly to
pressure switch to avoid possible fire and property damage.

Single Phase Motors - No Magnetic Starter

Single Phase Motors - With Magnetic Starter

WARNING

N

O

N

P

R

O

Q

S

Wiring Installation

«
...
10
11
12
13
14
...
»

Summary of Contents for PP05H080I1









































Reviews:

No comments

Related manuals for PP05H080I1

Brand: Villager Pages: 141

Brand: KAESER Pages: 136

Brand: Frick Pages: 78

Brand: Robust Pages: 48

Brand: Rockworth Pages: 3

Brand: BE Pages: 44

Brand: Senco Pages: 16

Brand: California Air Tools Pages: 16

BrakeMaster 8310

Brand: Roadmaster Pages: 2

Brand: Roadmaster Pages: 2

Brand: XTM Pages: 2

Brand: Powerex Pages: 16

Brand: Sanborn Mfg Pages: 24

Brand: Eastwood Pages: 12

Brand: Danfoss Pages: 4

Brand: Danfoss Pages: 10

Brand: Danfoss Pages: 12

Brand: Hino Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands