Polar Air PP05H080I1 Operating Instructions Manual Download

Page: 7 / 40

Polar Air Electric Operated, Piston Compressors

Do not operate unit if damaged during shipping, handling or use.
Damage may result in bursting and cause injury or property damage.

WARNING

Make sure lift operator stays aware while moving compressor.

2. Be sure load is secure and well balanced before moving the compressor.

3. Make sure forks are fully engaged and level before lifting or moving compressor.

4. Keep load as low as possible and observe safe operating practices.

Carefully inspect all lifting equipment and make sure it is in

good condition. Rated capacity should exceed compressor

weight. Make sure lifting hook has a functional safety latch

or equivalent and is properly attached to lifting feature.

2. Make sure lifting points are in good condition and tighten

any loose nuts or bolts before lifting.

3. Use provided lifting feature or appropriate sling. A sling must

be used when moving compressor with a helicopter or other

air borne equipment. Be sure to follow OSHA standards 29

CFR 1910 Subpart N.

4. Use guide ropes or equivalent to prevent twisting or

swinging of the compressor while it is in the air and

NEVER

attempt to lift in high winds. Keep compressor as

low to the ground as possible.

5. Keep persons away and make sure no one is under the compressor while it is lifted.

6. Only use lifting features provided for entire compressor package.

NEVER

use bolts or other hooks on

invididual components to move the compressor.

Make sure to put compressor on a level surface that can support the weight of the compressor and loading

equipment.

Forklift Safety

Lifting Safety

Summary of Contents for PP05H080I1









































Search results

Summary of Contents for PP05H080I1

Reviews:

Related manuals for PP05H080I1

Brands by name

Popular brands

Polar Air PP05H080I1, Operating Instructions Manual

Search results

Summary of Contents for PP05H080I1

Reviews:

Related manuals for PP05H080I1

Brands by name

Popular brands