background image

 
 

 

WWW.PME.COM 

TECHNICAL SUPPORT: [email protected] | (760) 727-0300 

PG. 7 

THIS DOCUMENT IS PROPRIETARY AND CONFIDENTIAL. © 2021 PRECISION MEASUREMENT ENGINEERING, INC. ALL RIGHTS RESERVED. 

 

 

1.2 Installation Instructions 

Begin miniWIPER operation by setting the Wiper Control Switch to "WIPE" as described in Chapter 
3 of this manual. Begin Cyclops 7 Logger operation as described in the Cyclops 7 Logger Manual.  
Operation of both units must begin now since their control switches will not be accessible after they 
are mounted in the bracket. 

The Cyclops 7 Logger comes with a sensor guard (sensor shade) installed. This will need to be 
removed so the Cyclops 7 Logger can be used in conjunction with the miniWIPER. The sensor 
retainer that holds the Cyclops 7 sensor in place must remain installed. Install the included wiper 
sensor guard to replace the sensor shade. The bracket will grip the sensor retainer and the wiper 
sensor guard. 

 

Construct the bracket from the parts supplied 
by PME as shown in the picture to the left. 
Install bolts and nuts loosely. Please note that 
the wiper and Cyclops 7 have different 
diameters and so will only fit on one side or the 
other of the bracket. Make sure that the paired 
brackets match up to form the correct diameter 
holes. The miniWIPER will be installed in the 
same diameter holes while the Cyclops 7 
Logger needs the smaller sized hole at the top. 
This will allow the Cyclops 7 Logger to slide 
through the larger hole and into the smaller 
hole, which will grip the wiper sensor guard. 

 

Rotate miniWIPER and Cyclops 7 Logger until 
the Cyclops 7 Logger optical surface and the 
wiper pulley axes are as shown in the pictures. 

Summary of Contents for Cyclops-7



























Reviews: