0507060400/010920/M DraftMax Basic | DraftMax Ultra
5
L Wheel set
Wheel set to facilitate internal transport of the downdraft
table.
Also handy to move the downdraft table forward for service
purposes to the membrane valves, if necessary (applies to
DraftMax Ultra only).
M Dust tray lid
(not shown)
When the dust drawer below the filter cartridges needs to be
emptied, the lid over the dust drawer, the plastic bag and the
personal protection equipment enable dust free removal.
Fig. 2.4
B
C (x2)
E
F
H
I
L (x5)
Options
3
SAFETY INSTRUCTIONS
General
The manufacturer does not accept any liability for
damage to the product or personal injury caused by
ignoring of the safety instructions in this manual, or
by negligence during installation, use, maintenance, and repair
of the product mentioned on the cover of this document and
any corresponding accessories.
Specific working conditions or used accessories may require
additional safety instructions. Immediately contact your
supplier if you detect a potential danger when using the
product.
The user of the product is always fully responsible for
observing the local safety instructions and regulations.
Observe all applicable safety instructions and
regulations.
User manual
- Everyone working on or with the product, must be familiar
with the contents of this manual and must strictly observe
the instructions therein. The management should instruct the
personnel in accordance with the manual and observe all
instructions and directions given.
- Do not change the order of the steps to perform.
- Keep the manual with the product.
Users
- The use of this product is exclusively reserved to authorised,
trained and qualified users. Temporary personnel and
personnel in training can only use the product under
supervision and responsibility of skilled engineers.
- Stay alert and keep your attention to your work. Do not use
the product when you are under the influence of drugs,
alcohol or medicine.
- The product is not to be used by children or persons with
reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given
supervision or instruction.
- Children must be supervised not to play with the product.
Intended use
2
The product has been designed as a workbench with
integrated extraction and filtration facility for welding and
grinding purposes, provided the appropriate options have been
installed (refer to paragraph 2.3). With the optional HEPA set
the product is suitable to extract welding fume from high
alloyed steel, i.e. steel with a nickel and chromium content of
>30%. This corresponds with welding fume class “W3”. Using
the product for other purposes is considered contrary to its
intended use. The manufacturer accepts no liability for any
damage or injury resulting from such use. The product has
been built in accordance with state-of-the-art standards and
recognised safety regulations. Only use this product when in
technically perfect condition in accordance with its intended
use and the instructions explained in the user manual.
Technical specifications
Do not change the specifications given in this manual.
Modifications
Modification of (parts of) the product is not allowed.
Installation
- The installation of this product is exclusively reserved to
authorised, trained and qualified engineers.
- The electric connection must be executed in accordance with
the local codes and requirements. Ensure compliance with
the EMC regulatory arrangements.
- During installation, always use Personal Protective
Equipment (PPE) to avoid injury. This also applies to persons
who enter the work area during installation.
- Do not install the product in front of entrances and exits
which must be used for emergency services.
- Make sure that the workspace is well illuminated.
- Stay alert and keep your attention to your work. Do not
install the product when you are under the influence of
drugs, alcohol or medicine.
- Air containing particles such as chromium, nickel, beryllium,
cadmium, lead etc., should never be recycled. This air must
always be brought outside the working area.
2. “Intended use” as explained in EN-ISO 12100-1 is the use for which the
technical product is suited as specified by the manufacturer, inclusive of his
directions in the sales brochure. In case of doubt it is the use which can be
deduced from the construction, the model and the function of the technical
product which is considered normal use. Operating the machine within the
limits of its intended use also involves observing the instructions in the user
manual.
