background image

 

PlexWriter 40/12/40A Installation and Users Manual  

41

 

Appendix B: Technical Support  

Store Plextor’s e-mail, web site, phone, and fax numbers in a convenient location. 
Keep your drive’s serial number and a copy of your sales receipt handy as well. 
 
If you experience a problem while installing or operating your PlexWriter drive, 
please refer first to the relevant sections of this manual regarding setup and 
installation (Chapters 1–3). If you do not uncover the solution there, please refer next 
to the maintenance and troubleshooting chapter that begins on page 29. You may 
also wish to refer to the Frequently Asked Questions (FAQ) section of our web site 
to assist you in troubleshooting the problem on your own. 
 

NOTE: We encourage you to go the Plextor web site (www.plextor.com) before 
attempting to contact Technical Support. The answers to the most common questions 
callers ask can be found quickly in the support area. Select PlexHelper for online 
troubleshooting or FAQs for common questions. 

 
If you have not been successful in your quest, our Technical Support Department 
will help you solve problems that relate specifically to your PlexWriter drive. In 
many cases, a problem that appears to be caused by your PlexWriter actually 
originates in another part of your computer. In such instances, our technical support 
staff will try to help you identify the part at fault and will refer you to the 
manufacturer of that part for further assistance. 
 

How to Contact Us 

There are several ways for you to contact Plextor’s Technical Support Department: 
 

• 

Visit our web site (www.plextor.com) for answers to Frequently Asked 
Questions. 

• 

Send us e-mail at [email protected]. Include your telephone number and the 
hours during which you can be reached. Be as detailed as possible in describing 
your problem. Please include system configuration, hardware and software, as 
well as versions of drivers used. 

• 

Call 800-886-3935 and select the tech support option. 

Summary of Contents for PlexWriter 40/12/40A

























































Reviews: