manualshive.com logo in svg

PLAYSTAR Little Sprout Grow With Me Toddler Tunnel, Safety Manual & Assembly Instructions

The PLAYSTAR Little Sprout Grow With Me Toddler Tunnel is an innovative and versatile playset designed to engage and entertain your little one. With its adjustable design, it grows with your child, ensuring years of fun. For your peace of mind, a detailed Safety Manual & Assembly Instructions are available for free download at {website name}, providing you with all the necessary information to assemble and use the tunnel safely.

Share
Download
background image

16

Top-Down View

Tunnel Side

Front

Right Hand 

Side

Left Hand 

Side

If you are attaching a slide to the Toddler Tunnel, TWO sides of the upper decking must 

remain open. One for the Slide and one for the Rock Wall. 
Decide where to place the rock wall and the slide. Enclose the remaining side, following 

the steps in the next pages.

If you are NOT attaching a slide to the Toddler Tunnel, ONLY one side of the upper decking 

must remain open for the Rock Wall. 
Decide where to place the rock wall. Enclose the remaining two sides, following the steps 

in the next pages.

STOP

STOP

Summary of Contents for Little Sprout Grow With Me Toddler Tunnel













































Reviews:

No comments

Related manuals for Little Sprout Grow With Me Toddler Tunnel

Raven SC1 Accessory Installation Manual preview
SC1
Brand: Raven Pages: 27
Raven SC1 Calibration And Operation Manual preview
SC1
Brand: Raven Pages: 79
Raven SC1 Calibration & Operation Manual preview
SC1
Brand: Raven Pages: 88
Eagle Eye SG-1000 User Manual preview
SG-1000
Brand: Eagle Eye Pages: 21
Labomed Magna User Manual preview
Magna
Brand: Labomed Pages: 67
KUHN FC3160TCD Operator'S Manual preview
FC3160TCD
Brand: KUHN Pages: 112
stilum Silva villa Maintenance Instructions preview
Silva villa
Brand: stilum Pages: 3
Falltech DuraTech 45' 3-Way Retrieval SRL-R User Instruction Manual preview
DuraTech 45' 3-Way Retrieval SRL-R
Brand: Falltech Pages: 18
Walimex Pro LED Niova 150-F Pro 150W Bi Color Manual preview
LED Niova 150-F Pro 150W Bi Color
Brand: Walimex Pro Pages: 56
Swing-N-Slide TIMBER-BILT TB 1405 Assembly Instructions preview
TIMBER-BILT TB 1405
Brand: Swing-N-Slide Pages: 4
STARPLAY 01-985 Assembly Instructions Manual preview
01-985
Brand: STARPLAY Pages: 12
PARO sonic User Manuel preview
sonic
Brand: PARO Pages: 20
KARAM Horizon PN 4000 Product Information preview
Horizon PN 4000
Brand: KARAM Pages: 22
Pulse LOGO30 Manual preview
LOGO30
Brand: Pulse Pages: 4
Denon MC6000MK2 Quick Start Manual preview
MC6000MK2
Brand: Denon Pages: 9
Gorilla Playsets Blue Ridge Big Skye I Assembly Manual preview
Blue Ridge Big Skye I
Brand: Gorilla Playsets Pages: 136
Chauvet Q-Roll 150 Supplementary Manual preview
Q-Roll 150
Brand: Chauvet Pages: 1
Esco HURRICANE 20387 Instruction Manual preview
HURRICANE 20387
Brand: Esco Pages: 8

Brands by name

Popular brands

Load more brands