manualshive.com logo in svg

PLAYSTAR Little Sprout Grow With Me Toddler Tunnel, Safety Manual & Assembly Instructions

The PLAYSTAR Little Sprout Grow With Me Toddler Tunnel is an innovative and versatile playset designed to engage and entertain your little one. With its adjustable design, it grows with your child, ensuring years of fun. For your peace of mind, a detailed Safety Manual & Assembly Instructions are available for free download at {website name}, providing you with all the necessary information to assemble and use the tunnel safely.

Share
Download
background image

10

Items for STEP 4:

  (1) 

2" x 4" x 21

Z\x

" board

  (6) 

#8 x 2

Z\x

" deck screws

Pre-drill the 2" x 4" x 21

Z\x

" board at the dimensions 

shown.

Attach pre-drilled 2" x 4" x 21

Z\x

" board as shown. 

Make sure assembly remains square while 
securing with #8 x 2

Z\x

" deck screws.

SEE PAGES 6 AND 7 FOR 

HOLE PATTERNS

A

A

D

2" x 4" x 21

¹⁄₂

"

10

³⁄₄

"

Flush

90º

Summary of Contents for Little Sprout Grow With Me Toddler Tunnel













































Reviews:

No comments

Related manuals for Little Sprout Grow With Me Toddler Tunnel

MacDon D65 Installation Instructions Manual preview
D65
Brand: MacDon Pages: 74
Qtx SURGE User Manual preview
SURGE
Brand: Qtx Pages: 6
Amazone UG 2200 Special Operating Manual preview
UG 2200 Special
Brand: Amazone Pages: 252
MD SPORTS AH060Y20010 Assembly Instructions Manual preview
AH060Y20010
Brand: MD SPORTS Pages: 15
hexinverter Mutant Bassdrum User Manual preview
Mutant Bassdrum
Brand: hexinverter Pages: 3
Megger TTR20 Instruction Manual preview
TTR20
Brand: Megger Pages: 60
Tektronix DPO2304SX Printable Help preview
DPO2304SX
Brand: Tektronix Pages: 920
Würth 0715 53 220 Translation Of The Original Operating Instructions preview
0715 53 220
Brand: Würth Pages: 76
U.S. General 94190 Assembly And Operating Instructions Manual preview
94190
Brand: U.S. General Pages: 8
Beta 1759HD Instructions Manual preview
1759HD
Brand: Beta Pages: 12
Robert Juliat 1011+ Technical File preview
1011+
Brand: Robert Juliat Pages: 48
Automotive ET2134 Instruction Manual preview
ET2134
Brand: Automotive Pages: 7
Falltech 727630LE User Instruction Manual preview
727630LE
Brand: Falltech Pages: 43
Briteq LED UV-GUN 100W Operation Manual preview
LED UV-GUN 100W
Brand: Briteq Pages: 10
JB Systems DYNAMO 250 Operation Manual preview
DYNAMO 250
Brand: JB Systems Pages: 44
Eaton FlexiTech SE CGLine+ Series Manual preview
FlexiTech SE CGLine+ Series
Brand: Eaton Pages: 7
YOKOGAWA M1233SR How To Use preview
M1233SR
Brand: YOKOGAWA Pages: 2
Parallax 28014 Quick Start Manual preview
28014
Brand: Parallax Pages: 4

Brands by name

Popular brands

Load more brands