Playnation 2300 Manual Download Page 98

Page: 98 / 131

STEP 54: UPPER ROOF BOARDS

1: PLACE A 1 X 6 X 36-5/8" UPPER ROOF BOARD ON TOP OF THE ROOF SUPPORTS, FITTING THE

TONGUE END INTO THE GROOVE END OF THE ROOF STARTER. EACH SIDE OF THE ROOF GETS SIX

ROOF BOARDS.

2: FASTEN THE UPPER ROOF BOARDS TO THE ROOF SUPPORTS WITH 1-1/2" WOOD SCREWS.

3: PLACE A 1 X 4 X 36-5/8" UPPER ROOF FINISHER ON THE ENDS OF THE ROOF ASSEMBLY AND

FASTEN WITH 1-1/2" WOOD SCREWS.

TIP: USE THE INSTRUCTIONS PROVIDED WITH THE DORMER TO BUILD IT. INSTALL THE FIFTH ROOF

BOARD AND INSTALL THE DORMER ACCORDING TO THE DORMER INSTRUCTIONS. THEN FINISH

INSTALLING THE REMAINING ROOF BOARDS AND FINISHER. ALSO NOTE THAT THERE IS ONE

DORMER ON EACH SIDE OF THE ROOF.

ROOF BOARD

UPPER

(FIFTH ONE)

1 X 4 X 36-5/8"

WOOD SCREW

1-1/2"

OF THE ROOF)

ROOF FINISHER

DORMER

(ONE EACH SIDE

1 X 6 X 36-5/8"

UPPER

ROOF BOARD

Summary of Contents for 2300




































































































































Search results

Summary of Contents for 2300

Reviews:

Related manuals for 2300

Brands by name

Popular brands

Playnation 2300, Manual

Search results

Summary of Contents for 2300

Reviews:

Related manuals for 2300

Brands by name

Popular brands