Playnation 2300 Manual Download Page 47

Page: 47 / 131

2 X 6 X 47-1/2"

BOTTOM

5/16" WASHER

5/16" X 4-1/2"HEX BOLT

PANEL BOARD

(OFFSET DOWN)

4 X 4 X 86-1/8"

CORNER POST

RIGHT

FRONT OF FORT

2 X 6 X 47-1/2"

TOP

PANEL BOARD

(OFFSET DOWN)

2 X 6 X 47-1/4"

BOTTOM SANDBOX BOARD

(OFFSET DOWN)

STEP 3: ASSEMBLING THE RIGHT SIDE FRAME

1: LAY THE 2 X 6 X 47-1/4" BOTTOM SANDBOX BOARD ON TOP OF THE RIGHT SIDE CORNER POSTS AT

THE BOTTOM OF THE CORNER POSTS. THE HOLES IN THE SANDBOX BOARD MUST BE OFFSET DOWN.

2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX

BOARD TO THET-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

3: LAY THE 2 X 6 X 47-1/2" BOTTOM PANEL BOARD ON TOP OF THE RIGHT SIDE CORNER POSTS IN THE

MIDDLE OF THE CORNER POSTS. THE HOLES IN THE BOTTOM PANEL BOARD MUST BE OFFSET DOWN.

4: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE BOTTOM HOLES OF THE BOTTOM

PANEL BOARD TO THE T-NUTS INSTALLED ON THE CORNER POSTS. THE TOP HOLES WILL BE USED LATER.

5: LAY THE 2 X 6 X 47-1/2" TOP PANEL BOARD ON TOP OF THE RIGHT SIDE CORNER POSTS. THE HOLES IN

THE TOP PANEL BOARD MUST BE OFFSET DOWN.

6: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE TOP PANEL

BOARD TO THE T-NUTS INSTALLED ON THE CORNER POSTS.

7: DO NOT INSTALL LAG SCREWS AT THIS TIME.

Summary of Contents for 2300




































































































































Search results

Summary of Contents for 2300

Reviews:

Related manuals for 2300

Brands by name

Popular brands

Playnation 2300, Manual

Search results

Summary of Contents for 2300

Reviews:

Related manuals for 2300

Brands by name

Popular brands