Playnation 2300 Manual Download Page 111

Page: 111 / 131

NOTE: YOU MAY TIE UP

TO THREE

KNOTS SPACED ABOUT

18" APART TO AID IN CLIMBING.

TIE A KNOT AND THREAD THE ROPE

THROUGH THE BACK SIDE OF THIS

HOLE IN THE ROPE LADDER SUPPORT

STEP 67: INSTALLING THE ROCK WALL ROPE

1: TIE A KNOT AT ONE END OF THE 10' ROPE AND THREAD IT THROUGH THE BACK SIDE OF THE

HOLE IN THE ROPE LADDER SUPPORT.

2: THE UNTIED END WILL GO THROUGH THE HOLE OF THE BOTTOM ROCK WALL BOARD. TIE A

SECURE KNOT AT THE END MAKING SURE THAT THE ROPE IS TIGHT AND WILL NOT WRAP

AROUND YOUR HAND. IF THE ROPE WRAPS AROUND YOUR HAND IT IS TOO LOOSE. UNTIE ONE

END AND THEN RETIE IT UNTIL IT NO LONGER WRAPS AROUND YOUR HAND.

HINT: TO REDUCE THE AMOUNT OF SLACK IN THE ROPE, LIFT THE ROCK WALL ASSEMBLY

SLIGHTLY WHEN TYING THE KNOT IN THE BOTTOM ROCK WALL BOARD. WHEN YOU LOWER THE

ASSEMBLY, THE ROPE WILL TIGHTEN.

103

Summary of Contents for 2300




































































































































Search results

Summary of Contents for 2300

Reviews:

Related manuals for 2300

Brands by name

Popular brands

Playnation 2300, Manual

Search results

Summary of Contents for 2300

Reviews:

Related manuals for 2300

Brands by name

Popular brands