Playnation 2300 Manual Download Page 64

Page: 64 / 131

34 "

STEP 20: ATTACHING THE ROCK WALL

1: PLACE THE ROCK WALL INTO POSITION CENTERED ON THE FRONT - LEFT CUT OUT AREA OF THE

FORT AS SHOWN BELOW. THE GREEN BRACKETS SHOULD BE 3/4" ABOVE THE BOTTOM OF THE

FRONT FACE BOARD. USING THE 90 GREEN BRACKETS AS A TEMPLATE; DRILL A 3/8” HOLE

THROUGH THE FRONT FACE BOARD.

2: GO UNDERNEATH THE DECK TO INSERT A T-NUT INTO THE BACKSIDE OF THE 3/8” HOLES IN THE

FRONT FACE BOARD.

3: ATTACH THE ROCK WALL WITH 5/16 X 1-1/2” BOLTS AND 5/16” WASHERS.

4: WHEN THE BRACKETS ARE SECURE, AND THE ROCK WALL IS IN ITS FINAL POSITION; TIGHTEN THE

5/16 X 1-1/2” BOLTS ON THE ROCK WALL SIDES.

ROCK WALL

(CENTER IT IN THE CUT

OUT AREA OF THE

FRONT FACE BOARD.)

5/16" WASHER

HEX BOLT

5/16" X 1-1/2"

T-NUT

Summary of Contents for 2300




































































































































Search results

Summary of Contents for 2300

Reviews:

Related manuals for 2300

Brands by name

Popular brands

Playnation 2300, Manual

Search results

Summary of Contents for 2300

Reviews:

Related manuals for 2300

Brands by name

Popular brands