PlayNation Play Systems 1500DT Manual Download | Manualshive

Page: 105 / 145

background image

TELESCOPE STAND

TELESCOPE

1-1/4" WOOD SCREWS

TELESCOPE BRACKETS

CENTER

POST

STEP 41: MOUNTING THE TELESCOPE

1: WITH THE 1-1/4" WOOD SCREWS PROVIDED IN THE TELESCOPE BAG, FASTEN ONE OF THE SQUARE

TELESCOPE BRACKETS TO THE FRONT TOP PANEL BOARD ON THE SLIDE SIDE OF THE CENTER POST.
2: PLACE THE TELESCOPE STAND AND TELESCOPE INTO THE SLOT OF THE TELESCOPE BRACKET.
3: FASTEN THE REMAINING TELESCOPE BRACKET TO THE OPPOSITE SIDE THAT THE FIRST TELESCOPE BRACKET

WAS INSTALLED ON WITH 1-1/4" WOOD SCREWS PROVIDED WITH THE TELESCOPE.

95

«
...
103
104
105
106
107
...
»

Summary of Contents for 1500DT


















































































































































Reviews:

No comments

Related manuals for 1500DT

Brand: Hagie Pages: 61

Brand: Campbell Pages: 18

Brand: Eclipse Combustion Pages: 46

Brand: EAW Pages: 2

Brand: YOKOGAWA Pages: 75

Brand: Zero88 Pages: 26

Brand: Quadro mdb Pages: 9

Brand: NAMYSLO Pages: 13

Brand: Chroma Pages: 198

Brand: EZ Digital Pages: 53

Pathport QUATTRO

Brand: Pathway connectivity solutions Pages: 9

Brand: P.Lindberg Pages: 26

Brand: Zipper Mowers Pages: 50

Brand: TATU Pages: 84

Brand: KUKKO Pages: 2

Brand: stilum Pages: 2

Brand: Kandolite Pages: 15

Brand: BK Precision Pages: 139

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands