manualshive.com logo in svg

Planex SWP-0224FP, User Manual, Page: 9 / 124

Share
Download
Planex SWP-0224FP User Manual Download Page 9

SWP-0224FP 24PORT L2 INTELLIGENT  PoE SWITCH User’s Manual 

9 

1 

Introduction 

Congratulations on becoming the owner of the SWP-0224FP L2 managed 
switch! You may now manage your LAN (local area network) through a 
friendly and powerful user interface. 

This user guide tells you how to set up the SWP-0224FP L2 managed 
switch, and how to customize its configuration to get the most out of this 
product. 

1.1 

L2 managed features 

• 

24 10/100/1000BASE-TX auto-sensing Fast Ethernet ports 

• 

Two 10/100/1000BASE-T auto-sensing Gigabit Ethernet switching port 

• 

Two small form factor (SFP) Gigabit interface converter (GBIC) slots 

• 

802.1D/802.1w transparent bridge/spanning tree protocol/rapid spanning 
tree protocol 

• 

8K MAC address cache with hardware-assisted aging 

• 

802.3x flow control 

• 

802.1Q-based tagged VLAN, up to 256 VLANs 

• 

802.1p class of service, 4 queues per port 

• 

IGMP snooping support ( See 4.5.5 IGMP snooping ) 

• 

802.3ad link aggregation (manual and LACP), up to 15 trunk groups 

• 

Port Mirroring 

• 

802.1X port-based network access control 

• 

RADIUS remote authentication dial-in user service 

• 

RMON: support 4 groups (1, 2, 3, 9) 

• 

SNMP v1, v2, v3 

• 

MIB-II 

• 

Enterprise MIB for PSU, fan, and system temperature, voltage 

• 

Telnet or SSH remote login 

• 

FTP for firmware update and configuration backup 

• 

Syslog. 

Summary of Contents for SWP-0224FP





























































































































Reviews:

No comments