manualshive.com logo in svg

Planex SWP-0224FP, User Manual, Page: 35 / 124

Share
Download
Planex SWP-0224FP User Manual Download Page 35

SWP-0224FP 24PORT L2 INTELLIGENT  PoE SWITCH User’s Manual 

35 

4.4 

Physical Interface  

The Physical Interface displays the Ethernet port status in real time. You can 
configure the port in following fields: 

Port: select the port to configure 

Admin: disable/enable the port 

Mode: set the speed and duplex mode 

Flow Control: enable/disable 802.3x flow control mechanism 

Port Status Window: displays the following information for each port 

a) 

Link status: the link speed and duplex for an existing link, 
otherwise link is down 

b) 

State: the STP state 

c) 

Admin: the setting value to disable or enable the port 

d) 

Mode: the setting value for link speed and duplex mode 

e) 

Flow Control: the setting value to enable or disable 802.3x flow 
control mechanism 

Select the corresponding port number and configure the port setting, then click 

on the 

 button. The field you change will update the content of the 

display window. However, the new settings do not take effect until the “Save 
Configuration” is executed. 

 

 

 

Summary of Contents for SWP-0224FP





























































































































Reviews:

No comments