Planex SWP-0224FP User Manual Download Page 106

Page: 106 / 124

SWP-0224FP 24PORT L2 INTELLIGENT PoE SWITCH User’s Manual

106

6.2

Configuration restore

Configuration restore can be done with ftp. In MS-DOS, the configuration

restore is done as follows.
SWP-0224FP’s IP address is “192.168.1.1”.
PC’s (for ftp client) IP address is “192.168.1.10”.

PC is connected with SWP-0224FP ,and , execute ftp according to the
following procedures.

C:\>ftp 192.168.1.1

(Connect to SWP-0224FP by ftp)

Connected to 192.168.1.1.
220 PLANEX SWP-0224FP FTP version 1.0 ready

User (192.168.1.1:(none)): admin

(Enter the User ID of SWP-0224FP)

331 Enter PASS command

Password:

(Enter null if SWP-0224FP’s setting is default)

230 Logged in

ftp> put backup

(Restore configuration of SWP-0224FP by ftp)

200 Port command okay
150 Opening data connection for RETR backup
226 File sent OK
ftp: 52684 bytes sent in 0.00Seconds 52684000.00Kbytes/sec.

ftp> bye

(Exit ftp mode)

221 System is rebooting, bye

(SWP-0224FP reboots automatically)

Summary of Contents for SWP-0224FP





























































































































Search results

Summary of Contents for SWP-0224FP

Reviews:

Planex SWP-0224FP, User Manual, Page: 106 / 124

Search results

Summary of Contents for SWP-0224FP

Reviews: