Planet WDRT-1202AC User Manual Download Page 53

Page: 53 / 89

User Manual of WDRT-1202AC

-47-

5.2.3 LAN

Figure 5-2-19 LAN

Object

Description

LAN IP Address

Router’s LAN IP.
The default is

192.168.1.1

. You can change it according to your

needs.

Subnet Mask

Router’s LAN subnet mask.

Local Domain Name

Set the domain name of the server.

Enable DNS Relay

Enable or disable the DNS relay.

Enable Secondary LAN IP

Address

Enable or disable secondary LAN IP address.

DHCP Server Status

If it is selected, the router serves as the DHCP server and
automatically assigns IP addresses to all computers in the LAN.

IP Address Range

Enter the start and end IP address of all the available successive
IPs.

Lease Time

Select the time for using one assigned IP from the dropdown list.
After the lease time, the AP automatically assigns new IP
addresses to all connected computers.

Always Broadcast

This causes the DHCP server to respond to requests with a
broadcast instead of unicast.

Summary of Contents for WDRT-1202AC


























































































Search results

Summary of Contents for WDRT-1202AC

Reviews:

Related manuals for WDRT-1202AC

Brands by name

Popular brands

Planet WDRT-1202AC, User Manual

Search results

Summary of Contents for WDRT-1202AC

Reviews:

Related manuals for WDRT-1202AC

Brands by name

Popular brands