Planet WDRT-1202AC User Manual Download Page 17

Page: 17 / 89

User Manual of WDRT-1202AC

-11-

LED

STATE

FUNCTION

PWR

Device power on

Off

Device power off

2.4GHz

The 2.4GHz Wi-Fi is activated.

Flash

Device is transmitting data wirelessly over 2.4GHz.

Off

The 2.4GHz Wi-Fi is disabled.

5GHz

The 5GHz Wi-Fi is activated.

Flash

Device is transmitting data wirelessly over 5GHz.

Off

The 5GHz Wi-Fi is disabled.

WAN

Link is established.

Flash

Packets are transmitting or receiving.

Off

WAN port is not connected.

USB

USB connection is established.

Flash

Data is being transmitted.

Off

USB connection is not established.

Table 2-1

LED Indications

2.1.3 Rear Panel

The rear panel provides the physical connectors connected to the power adapter and any other network device.

Figure 2-4

shows the rear panel of the WDRT-1202AC.

Summary of Contents for WDRT-1202AC


























































































Search results

Summary of Contents for WDRT-1202AC

Reviews:

Related manuals for WDRT-1202AC

Brands by name

Popular brands

Planet WDRT-1202AC, User Manual

Search results

Summary of Contents for WDRT-1202AC

Reviews:

Related manuals for WDRT-1202AC

Brands by name

Popular brands