background image

5

Chapter 2

Installation

This  section  describes  the  functionalities  of  the  Switch  components  and  guides  how  to 
install it on the desktop or shelf. Basic knowledge of networking is assumed. Please read 
this chapter completely before continuing.

2.1 Product Description

The PLANET Switch provides 16/24 10/100Mbps Fast Ethernet ports with 2 10/100/1000Mbps 
ports and 2-SFP interfaces (port #17/25, port#18/26), either TP or SFP per port. The two 
Gigabit ports either can be 1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX through 
SFP (Small Factor Pluggable) interface. The distance can be extended from 100 meters 
(TP), 550 meters (Multi-mode fiber), up to above 10/50/70/120 kilometers (Single-mode 
fiber). The Switch with non-blocking backplane and simplifies the task of upgrading your 
LAN to cater for increased bandwidth demand. 

Equipped with console, the Ethernet Smart Switch can be programmed for basic Switch 
management  functions  such  as  port  speed  configuration,  Port  Trunking,  VLAN,  QoS, 
bandwidth control and IGMP Snooping.

2.1.1 Product Overview

PLANET  FGSW-1820RS/FGSW-2620RS, the Switch is Ethernet Smart Switch with 16/24 
RJ-45  10/100Mbps  ports.  The  Switch  also  provides  up  to  two  10/100/1000Mbps  ports 
and 2-SFP interfaces for cost effective high-performance network connectivity. With its 
8.8Gbps non-blocking switch fabric, the PLANET Switch can also provide a local, high band-
width, Fast Ethernet network for your departmental backbone plus the ability to trunk four 
ports (800Mbps) to enable switch-to-switch backbone. The advanced functionality of the 
Switch eliminates traditional problems associated with the use of Ethernet. Users can be 
segregated using built-in VLAN functionality. These, coupled with the flexible fiber module 
options, make the Switch one of the best and most cost-effective MTU switch solutions for 
Multi-tenant service providers.

This  Switch  also  supports  store-and-forward  forwarding  scheme  to  ensure  low  latency 
and high data integrity, eliminates unnecessary traffic and relieves congestion on critical 
network paths. With an intelligent address recognition algorithm, Switch could recognize 
up to 8K different MAC address and enables filtering and forwarding at full wire speed. 

2.1.2 The Front Panel

Figure 2-1 shows front panel of FGSW-1820RS.

Figure 2-1 PLANET FGSW-1820RS Front Panel

Summary of Contents for FGSW-1820RS







































Reviews: