Planet Networking & Communication WNRT-617 User Manual Download Page 67

Page: 67 / 155

User’s Manual of WNRT-617

-60-

5.7 DHCP

There are three submenus under the DHCP menu (shown in

Figure 5-18

DHCP Settings

DHCP

Clients List

and

Address Reservation.

Click any of them, and you will be able to configure the

corresponding function.

Figure 5-18

The DHCP menu

5.7.1 DHCP Settings

Choose menu “

DHCP

→

DHCP Settings

”, you can configure the DHCP Server on the page (shown in

Figure 5-19

).The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server,

which provides the TCP/IP configuration for all the PC(s) that are connected to the Router on the LAN.

Figure 5-19

DHCP Settings

The page includes the following fields:

Object

Description

DHCP Server

Enable

Disable

the DHCP server. If you disable the Server, you must

have another DHCP server within your network or else you must

Summary of Contents for WNRT-617




























































































































































Search results

Summary of Contents for WNRT-617

Reviews:

Brands by name

Popular brands

Planet Networking & Communication WNRT-617, User Manual

Search results

Summary of Contents for WNRT-617

Reviews:

Brands by name

Popular brands