Planet Networking & Communication WNRT-617 User Manual Download Page 11

Page: 11 / 155

User’s Manual of WNRT-617

-4-

WPA-PSK / WPA2-PSK (TKIP/AES)

WPA / WPA2 (TKIP/AES)

WPA / WPA2 enterprise mode (802.1x authentication)

Provide wireless LAN ACL (Access Control List) filtering

Wireless MAC address filtering

Support WPS(WIFI Protected Setup )

Wireless Security

Enable/Disable SSID Broadcast

Support 802.11e WMM (Wi-Fi Multimedia)

Support Wireless Roaming

Wireless Advanced

Provide Wireless Statistics

Router Features

Internet Connection

Type

Shares data and Internet access for users, supporting following internet access:

PPPoE / Russia PPPoE

Dynamic IP

Static IP

Telstra Big Pond

PPTP / Russia PPTP

L2TP / Russia L2TP

NAT firewall with SPI (Stateful Packet Inspection)

NAT with ALG (Application Layer Gateway)

Built-in NAT server supporting Virtual Server, and DMZ

Built-in firewall with IP address filtering, Domain Name filtering, and MAC address filtering

Firewall

Support ICMP-FLOOD, UDP-FLOOD, TCP-SYN-FLOOD filter, DoS protection

Routing Protocol

Static Routing

VPN Pass-through

PPTP, L2TP, IPSec

Built-in DHCP server supporting static IP address distributing

Support UPnP, Dynamic DNS

Support Flow Statistics

IP & MAC Binding

IP / Protocol-based Bandwidth Control

LAN

Session Number: Max 5210

Web-based (HTTP) management interface

Remote management

SNTP time synchronize

Easy firmware upgrade

System Management

System Log supports auto mail and save to local host

OS Compatibility

Windows 7(32-bit/64-bit)

Windows Vista (32-bit/64-bit)

Windows XP

Mac OS X 10.4 and higher

Summary of Contents for WNRT-617




























































































































































Search results

Summary of Contents for WNRT-617

Reviews:

Brands by name

Popular brands

Planet Networking & Communication WNRT-617, User Manual

Search results

Summary of Contents for WNRT-617

Reviews:

Brands by name

Popular brands