manualshive.com logo in svg

Planet Networking & Communication WNRT-617, User Manual

Share
Download
Planet Networking & Communication WNRT-617 User Manual Download Page 18

User’s Manual of WNRT-617 

 

-11- 

Chapter 4.  Quick Installation Guide 

This chapter will show you how to configure the basic functions of your Wireless 3G Router using 

Quick Setup 

within minutes. 

 

A computer with wired Ethernet connection to the Wireless Router is required for the 

first-time configuration. 

4.1  Manual Network Setup - TCP/IP Configuration 

The default IP address of the WNRT-617 is 

192.168.1.1

. And the default Subnet Mask is 

255.255.255.0. These values can be changed as you desire. In this guide, we use all the default 

values for description. 

Connect the local PC to the LAN ports of the Router. And then you can configure the IP address for 

your PC in the following two ways. 

„

 

Obtain an IP address automatically   

„

 

Configure the IP address manually 

In the following sections, we’ll introduce how to install and configure the TCP/IP correctly in 

Windows 

XP

. First, make sure your Ethernet Adapter is working, and refer to the Ethernet adapter’s manual if 

needed. 

 

4.1.1  Obtain an IP Address Automatically 

Summary:  

„

 

Set up the TCP/IP Protocol in "

Obtain an IP address automatically

" mode on your PC. 

„

 

Then the WNRT-617 built-in DHCP server will assign IP address to the PC automatically. 

 

1.  Install TCP/IP component 

1)  On the Windows taskbar, click the 

Start

 button, point to 

Settings

, and then click 

Control 

Panel

. 

2) Click 

the 

Network and Internet Connections

 icon, and then click on the 

Network 

Connections

 tab in the appearing window. 

3) 

Right click the icon shown below, select Properties on the prompt window. 

Summary of Contents for WNRT-617




























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands