Planet Networking & Communication WNRT-617 User Manual Download Page 112

Page: 112 / 155

User’s Manual of WNRT-617

-105-

5.15 Dynamic DNS

Choose menu “

Dynamic DNS

”, and you can configure the Dynamic DNS function.

The Router offers the

DDNS

(Dynamic Domain Name System) feature, which allows the hosting of a

website, FTP server, or e-mail server with a fixed domain name (named by yourself) and a dynamic IP

address, and then your friends can connect to your server by entering your domain name no matter

what your IP address is. Before using this feature, you need to sign up for DDNS service providers

such as

. The Dynamic DNS client service

provider will give you a password or key.

5.15.1 Comexe.cn DDNS

If the dynamic DNS

Service Provider

you select is

www.comexe.cn

, the page will appear as shown in

Figure 5-61

Figure 5-61

Comexe.cn DDNS Settings

Summary of Contents for WNRT-617




























































































































































Search results

Summary of Contents for WNRT-617

Reviews:

Brands by name

Popular brands

Planet Networking & Communication WNRT-617, User Manual

Search results

Summary of Contents for WNRT-617

Reviews:

Brands by name

Popular brands